DUBBING (from deck A to deck B)

q Press the POWER switch q to the ON ( ¢ )

• When dubbing, the recording level and the Dolby

ENGLISH

MEMORY STOP

1. MEMORY STOP Operation

2. Display Back-up

position.

wLoad the cassette tape to be played in deck A and

the one to be recorded in deck !9, !6.

eSelect the type of tape transport with the REV. MODE button @0.

Reverse

Operation

mode

 

 

 

 

Dubbing is performed only for one

 

side.The decks stop when either

 

deck A or B reaches the end of the

 

tape.

 

 

 

The tape direction is reversed on

 

each deck when they reach the end

 

of the tape. (This is convenient for

 

dubbing to a tape with a different

 

length.)

 

 

RELAY

During dubbing of the side facing

or

you, the deck that first reaches the

 

NR coding will be the same as those of the

 

playback tape, regardless of the positions of the

 

INPUT LEVEL control and the DOLBY NR switch.

• When listening to the playback sound during

 

normal speed dubbing, set the DOLBY NR switch

 

to match the Dolby NR system with which the

 

playback tape was recorded. This will assure

 

correct sound reproduction, but does not affect the

 

recording.

•

The playback sound cannot be heard during high

 

speed dubbing.

•

Operation using the Rec/Rec Mute ( 4 ) and Rec

 

Pause ( 3 ) buttons of deck B is permitted during

 

normal speed dubbing.

• Buttons other than the Stop ( 2 ) button cannot be

 

used during high speed dubbing.

• In the normal speed dubbing mode, play signals are

 

only output from the DECK A LINE OUT jacks. In

 

the high speed dubbing mode, no sound is output.

(1)During recording or playback, the Memory Stop feature can be used to locate a particular point on the tape. Press the COUNTER MEMO button at the desired point.

(2)The MEMO indicator lights.

(3)When the Rewind ( 6 ) button is pressed during forward tape travel ( 1 ), or the Fast Forward ( 7 ) button is pressed during reverse tape travel ( 0 ), the tape is rapidly rewound (or advanced) until the counter indication of “‚‚‚‚” is reached.

•The Memory Stop feature will rewind or forward the tape to within _5 counts in the forward ( 1 ) direction (from “‚‚‚‚” to “_‚‚‚fi”) and to within

+5 counts in the reverse ( 0 ) direction (from “‚‚‚‚” to “‚‚‚fi”).

•The Memory Stop function operation independently in both directions for deck A and deck B.

Caution :

The COUNTER VALUE, MEMO, DIRECTION and REV. MODE functions are protected for approximately one month by a memory back-up.

Once the back-up period is up, the MEMO settings are set to off, the DIRECTION setting is set to 1, and the counter is reset to “‚‚‚‚”.

CASCADE end of the tape will stand by until the

other deck reaches the end of the

tape, then both decks will reverse

the tape direction together.

(Depending on the manufacturer, the

length of tapes having the same

2MANUAL DUBBING

•

With this function, the signal played on Deck A can

 

be recorded manually on the tape in Deck B.

•

The manual dubbing function is also used to record

 

the signal of the Deck A tape with which the

 

microphone input signal has been mixed onto the

If the memory stop operation is performed after repeated fast-forwarding or rewinding, the tape may not stop at the proper position.

recording time may differ somewhat.

Setting this mode permits the

arrangement of the beginning portion

of the opposite side of the tape.)

rTo begin normal speed dubbing, press the DUBBING SPEED NORMAL button r. The DUB indicator will light at this time.

To high speed dubbing, press the DUBBING SPEED HIGH button r.

The HIGH indicator will light at this time.

tTo stop dubbing, press the Stop ( 2 ) button !4of deck A or deck B.

tape in Deck B.

qPerform steps e to t in the “PLAYBACK” section on Deck A.

wPerform steps w to t in the “RECORDING”

section on Deck B. Set to Deck B INPUT SELECT switch to Deck A.

eSet deck A to the play mode and adjust the recording level using the INPUT LEVEL-B control y.

rConnect microphones to the MIC jacks !1and set the MIC MODE switch !2to the “REC” mode.

tSet the microphone input level with the MIC INPUT LEVEL control !3. Also set the MIC AGC

switch !0to “ON”.

yStart playback on Deck A and recording on Deck B.

NOTE :

This operation is not possible if the reverse mode is set to RELAY or CASCADE.

To prevent noise, set the MIC MODE switch to “off” when connecting microphones to the MIC jacks.

PRESET FUNCTION

•Use these functions to preset the DN-780R’s operation modes. These presets are stored in permanent memory, so they are not cleared even when the power is turned off.

•The preset procedure can be performed in the stop mode of both the deck A and deck B.

qPress the Stop ( 2 ) button !4on Deck A and the

Stop ( 2 ) button !4and REV. MODE button @0on Deck B simultaneously.

wPress the Play ( 1 ) button !4on Deck A and select the preset item.

Preset items :

1)Setting of number of cycles for “ ” or

“RELAY MODE”

2)Setting of power on play mode (on or off)

3)Setting of infrared remote control codes to be received

4)Infrared remote control sensor setting (on or off)

ePress the Play ( 1 ) button !4on Deck B to change the settings.

1)Number of cycles for the relay mode “Loop 01” : Stop relay play after 1 cycle.

*“Loop 05” : Stop relay play after 5 cycles. “Loop 10” : Stop relay play after 10 cycles.

2)Power on play setting (on/off) “P-on P on” : Power on play on

*“P-on P oFF” : Power on play off

3)Infrared remote control codes to be received *“rc dnon”: Receive Denon codes.

“rc rc-5”: RC-5 codes can be received.

4)Infrared remote control sensor setting (on/off) *“ir on”: Accept infrared remote control

signals.

“ir oFF”: Do not accept infrared remote control signals.

“*” indicates the default setting.

rThe preset mode is canceled when the Stop ( 2 ) button !4on Deck A or Deck B is pressed. The settings are written at this time.

11