ENGLISH

8SAMPLER

Sampler playback

Select the source of Sampler

1• Turn the ASSIGN switch y in the SAMPLER part to select the desired source.

Record in Sampler

When the A button i is pushed, the sound of the selected source is recorded to Sampler

2memory up to 8 seconds.

•The A button i flashes after recording starts.

•When the recording is completed, B button o lights up.

Setting B point / Stop recording

When the B button o is pushed during recording, the B point is set.

3• Recording continues for approximately 8 seconds without stopping after set B point.

•If the B point is not set, recording end point set as B point automatically.

Setting the Sampler sound level

The sound level (volume) can be set for Sampler.

4• To select “S_Level” turn the MODE knob u and push.

•Turn the MODE knob u and select between “–14 dB” and “+6 dB”.

Select Sampler play mode

You can select play mode for Sampler when Sampler playback stop.

Loop (default):

Sampler playback continues with looping. Single:

Sampler playback stops at B point. Stutter:

Sampler is played while the A button i is pressed and held down.

5-1Loop + Reverse:

Reverse Sampler playback continues with looping.

Single + Reverse:

Reverse Sampler stops at A point. Stutter + Reverse:

Reverse Sampler is played while the A button i is pressed and held down.

Exit B:

Sampler playback continues over B point up to recording length.

To select Loop/Reverse mode, turn the MODE knob u then push after recording and before playing.

qPlay mode:

•To select “P_Mode” turn the MODE knob u and push.

5-2

• Turn the MODE knob u and select

 

“Loop”, “Exit B”, “Single” or “Stutter”.

wPlay direction:

•To select “DirMode” turn the MODE knob u and push.

•Turn the MODE knob u and select “Forward” or “Reverse”.

Play Sampler sound

•Playback of the Sampler sound starts when the A button i is pushed after recording has

completed.

6• To stop the Sampler sound, push the MODE knob u.

•When the CROSSFADER ASSIGN switch !0 in the SAMPLER part is set A or B, you can perform the Sampler Fader Start by the Crossfader !8. See page 10.

Moving Sampler B point

•When the B button o is pushed during

7 Sampler playback, the B point moves to the point at which the button was pushed, and Loop playback from point A starts.

Setting the Sampler pitch

The sound pitch can be set for Sampler.

8• To select “S_Pitch” turn the MODE knob u and push.

•Turn the MODE knob u and select between “–100 %” and “+100 %”.

Clearing the Sampler data

9• While pressing the MODE knob u, push the A button i to clear the Sampler.

Monitoring the Sampler data

(SAMPLER CUE)

• When the SAMPLER CUE button !6 is

10pressed, you can check the Sampler data.

NOTE:

When the SAMPLER CUE button is lit, the Sampler sound is not output into the Crossfader or MASTER OUT.

Sampler A/B Trim

 

Select A-B Trim mode

1

• To select “A/BTrim” turn the MODE knob u

 

and push.

 

 

 

Select A point (in A-B Trim)

2

• Push the A button i.

 

• The A button i illumination flashes and Loop

 

playback starts.

 

 

 

Trim A point

3

• Turn the MODE knob u. You can move the A

 

point.

 

 

 

Save the A point

4

• Push the MODE knob u to save new the A

 

point.

 

 

 

Select B point (in A-B Trim)

5

• Select the A-B Trim mode and push the B

 

button o.

 

• The B button o illumination flashes.

 

 

 

Trim B point

6

• Turn the MODE knob u. You can move the B

 

point.

 

 

 

Save the B point

7

• Push the MODE knob u to save new the B

 

point.

 

 

9PFL (Pre Fader Level)

1.Press the SPLIT CUE button @4.

2.Press the CUE button !6that you wish to monitor 1~ 4 (make sure your source is playing).

3.Turn the GAIN control #5until the meters peak at the 0 dB level.

4.Perform your mix using the Crossfader !8or Ch. Fader !9at your desire.

NOTES:

•For proper operation, your channel levels should always be set to or left on reference line 8.

•This adjustment can be made even if the Ch. Fader is set to zero level.

12