Denon RCD-M38 Using an optimizing ﬁlter, Auto power on, Auto source selector function, Auto standby, Last function memory, Resetting the microprocessor

Symbols used to indicate buttons in this manual

Button located on both the main unit and the remote control

BUTTON

Button only on the main unit <BUTTON>

Button only on the remote control [BUTTON]

<8/–> <5> <1/3><SDB/TONE>

ON/STANDBY

[SLEEP]

[TUNER]

[CD 1/3] [USB/iPod 1/3]

[MENU]	[DOCK 1/3]
[MENU]	[ENTER/MEMO]
	[uio p]

Other functions

Using an optimizing ﬁlter

An optimizing ﬁlter suited for the properties of the speakers (SC-M37) can be used.

1Press [MENU].

2Use [ui] to select “SPK OPTIMISE”, then press the [ENTER/MEMO] or [p].3Use [ui] to select “ON”, then press the [ENTER/ MEMO] or [p].

The setting is entered.

ON The response is optimized for the speakers (SC-M37, sold separately).

OFF The response is ﬂat.

Auto power on

When the power is in standby, the power turns on when any of the buttons below other than ON/STANDBY is operated, and the

respective operation is performed.
• <5>...............................................	The disc tray opens.
• <1/3> for the different source ....	Playback of that source starts.
• [TUNER] ........................................	Playback of the tuner starts.

NOTE

The Auto Power On function cannot be used with control dock for iPod.

Auto source selector function

When one of the buttons below is pressed, it switches to that source and starts playback on that source.

• [CD 1/3] ...................	The source switches to “DISC” and the disc
	starts playing.

•[USB/iPod 1/3] ........The source switches to “USB” and the USB starts playing.

• [DOCK 1/3] ..............	The source switches to “AUX1/Dock” and the
• [TUNER] .....................	iPod starts playing.
• [TUNER] .....................	The source switches to “TUNER” and the
	band last set is tuned in.

ENGLISH

			Getting
	Auto standby		Started

	With the Auto standby ON, this unit will automatically enter the
			Basic
	standby mode after about 30 continuous minutes of stop mode with

	no operation.		BasicConnections

	2 [ENTER/MEMO] or [p].
	1 Press [MENU].
	Use [ui] to select “AUTO STANDBY”, then press
			Operations

	3 MEMO] or [p].
	Use [ui] to select “ON”, then press [ENTER/
	The setting is entered.
			Advanced

	NOTE
			Connections
	In the following situations, the Auto standby function does not operate.

	• When an iPod or USB memory device is connected to the USB port
	on the unit.
	• When the source is “TUNER”、“AUX1” or “AUX2”.
	• When the source is “AUX1/Dock”, and an iPod is connected to		Advanced
	• When the source is “PORTABLE IN” and a device is connected to
	control dock for iPod. (ASD-11R only)		Operations
	the portable jack.

	Last function memory
			Explanation
	When the power is turned back on, the settings are restored to as
	This stores the settings as they were immediately before going into
	the standby mode.		terms
	they were immediately before going into the standby mode.

	Resetting the microprocessor
			Troubleshooting
	Perform this procedure if the display is abnormal or if operations

	cannot be performed.
	When the microprocessor is reset, all the settings are reset to their
	default values.
			Speciﬁcations
	Plug the power cord into a power outlet while pressing
	1 Unplug the power cord.
	2 <8/–>and <SDB/TONE> simultaneously.
			Index
	• “INITIALIZE” is displayed.


	If “INITIALIZE” does not display in step 2, start over from step 1.