4

VENTILATION INSTALLATION OPERATION

To Start Heater

VENTILATION

WARNING: Provide at least a 6 square foot open- ing of fresh, outside air while running heater. If proper fresh, outside air ventilation is not provided, carbon monoxide poisoning can occur. Provide proper fresh, outside air ventilation before running heater.

FRESH OUTSIDE AIR OPENING REQUIREMENTS

HEATER SIZE

SQ. FT. OPENING

200,000 Btu/Hr

6.0

INSTALLATION

 

Fuel Gas

 

Propane

Fitting

Hose

 

Supply Valve

 

 

 

 

Regulator

 

 

Vent

 

 

(pointing down)

 

 

Propane Tank

Figure 2 - Regulator With Vent Pointing Down

WARNING: Review and understand the warnings in the Safety Information section, pages 2 and 3. They are needed to safely operate this heater. Follow all local codes when using this heater.

WARNING: Test all gas piping and connections for leaks after installation or servicing. Never use an open flame to check for a leak. Apply a mixture of liquid soap and water to all joints. Bubbles forming show a leak. Correct all leaks at once.

1.Provide propane supply system (see Propane Supply, page 3).

2.Connect fuel gas fitting on hose/regulator assembly to pro- pane tank(s). Turn fuel gas fitting counterclockwise into threads on tank. Tighten firmly using a wrench. IMPORTANT: Tighten regulator with vent pointing down. Pointing vent down pro- tects regulator from weather damage.

3.Connect hose to the valve inlet. Tighten firmly using a wrench. You must use the regulator supplied with heater even if pro- pane tank has one.

4.Open propane supply valve on propane tank(s) slowly. Note: If not opened slowly, excess-flow check valve on propane tank may stop gas flow. If this happens, you may hear a click inside the regulator assembly, this is the check valve closing. To re- set the excess-flow check valve, close propane supply valve and open it again slowly.

5.Check all connections for leaks. Apply mixture of liquid soap and water to gas joints. Bubbles forming show a leak that must be corrected.

6.Close propane supply valve.

Valve Inlet

AT

LO

PUSH

TO START

 

HI

Hose

Figure 3 - Hose and Valve Inlet

OPERATION

WARNING: Review and understand the warnings in the Safety Information section on pages 2 and 3. They are needed to safely operate this heater. Follow all local codes when using this heater.

TO START HEATER

1.Follow all installation, ventilation, and safety information.

2.Locate heater on stable and level surface. Make sure strong drafts do not blow on heater.

3.Open propane supply valve on propane tank(s) slowly. Note: If not opened slowly, excess-flow check valve on propane tank may stop gas flow. If this happens, you may hear a click inside the regulator assembly, this is the check valve closing. To re- set the excess-flow check valve, close propane supply valve and open it again slowly.

4.Turn control knob clockwise to the lowest position and push in (see Figure 4, page 5).

5.With the control knob pushed all the way in, press and release the piezo ignitor button (see Figure 4, page 5). Keep pressing piezo ignitor button until the burner lights. Hold control knob down for a maximum of 10 seconds while attempting ignition. If heater does not ignite, release control knob and wait 3 min- utes before attempting reignition.

Note: Keep hands and face away from outlet (around top of shell) of heater while attempting to start heater.

For morevisit www..com

103386-01G

Page 4
Image 4
Desa 200 owner manual Ventilation, Installation, Operation, To Start Heater

200 specifications

Desa 200 is an innovative and futuristic housing concept that aims to redefine modern living through sustainable design and advanced technology. Nestled in eco-friendly environments, Desa 200 epitomizes a lifestyle that harmonizes the tranquility of nature with the conveniences of urban living.

One of the standout features of Desa 200 is its commitment to sustainability. The community is built with environmentally friendly materials, ensuring minimal ecological impact. The use of solar panels is widespread, allowing residents to harness renewable energy for their everyday needs. This not only reduces the carbon footprint but also lowers energy costs significantly.

Incorporating smart home technologies, Desa 200 offers a seamless living experience. Each unit is equipped with advanced automation systems that allow residents to control lighting, heating, security, and appliances through their smartphones. The integration of Internet of Things (IoT) devices provides enhanced security and energy management, giving homeowners peace of mind.

Another noteworthy characteristic of Desa 200 is its emphasis on communal living. The design promotes social interaction through shared spaces, including parks, recreational areas, and community gardens. These spaces encourage residents to engage with one another, fostering a sense of belonging and community spirit that is often lacking in modern urban life.

Safety is a paramount concern in Desa 200, with features such as gated access, 24/7 surveillance, and well-lit pathways. These aspects, combined with a neighborhood watch program, ensure that residents feel secure in their homes and surroundings.

Desa 200 also prioritizes mobility and accessibility. The community is designed to accommodate various modes of transportation, including walking, cycling, and electric vehicles. Ample bike paths and pedestrian-friendly streets enhance the overall quality of life, making it easy for residents to navigate their environment.

In conclusion, Desa 200 is a forward-thinking housing model that embraces sustainability, advanced technology, and community living. With its eco-conscious design, smart home features, and a commitment to safety and accessibility, Desa 200 not only provides a comfortable living space but also paves the way for a greener, more connected future. This innovative approach serves as a blueprint for modern communities looking to balance the demands of contemporary life with environmental responsibility.