® BHDV34NA, PA
DIRECT-VENT FIREPLACE (NATURAL/PROPANE/LP)
OPERATING
FIREPLACE
Continued
1. After lighting, let pilot flame burn for |
about one minute. Turn gas control |
knob on the control valve to ON posi- |
tion. Turn variable control knob any- |
where between HI and LO. Slide the |
selector switch to the REMOTE posi- |
tion. Note: The burners may light if |
when selector switch was last turned |
off. You can now turn the burners on |
and off with either optional |
remote control unit. |
IMPORTANT: Do not leave the se- |
lector switch in the REMOTE posi- |
tion when the pilot is not lit. This will |
IMPORTANT: This remote control has been specially engineered to take an air temperature sample every 5.5 minutes in auto mode. It will not re- spond immediately to the tempera- ture setting being turned up or down.
IMPORTANT: The
3.Use the STATUS button on the hand- held remote control unit to see the operation mode being used and the temperature setting selected. A red light will come on beside the opera- tion mode being used.
4.To turn the burners off when operat- ing in the manual mode, press the OFF button. If operating in the auto mode, press the MAN button, then press the OFF button. The pilot will remain lit. IMPORTANT: To turn the pilot off, manually turn the gas control knob on the heater to the OFF position.
OPERATING
OPTIONAL BLOWER
ACCESSORY
Locate the blower controls by opening the lower louver panel on the fireplace. Blower controls are located on the left side of the switch bracket to the left just inside the louver panel.
Both the GA3700 manual blower and the DA3610T
drain the battery. |
IMPORTANT: Be sure to press the |
ON/OFF buttons on the |
remote control unit for up to 3 sec- |
onds to assure proper operation. |
GHRC Series Operation:
2a. Press the ON/OFF button to turn the burners on and off. When turning burners off, the pilot will remain lit.
GHRCT Series Operation:
Blower Control Knob (Optional Accessory)
OFF
ON
REMOTE
OFF
ON
Selector Switch in Remote Position
Variable Control Knob
N |
| L |
|
O |
| O | I |
T | F | O | H |
O |
|
| |
F |
|
| |
LIP |
|
|
|
|
|
|
|
Gas Control
Knob in On
Position
blower have an ON setting and an OFF setting. The blower will only run when the switch is in the ON position. In the OFF position, the blower will not operate.
Note for DA3610T Only: If you are using DA3610T blower with optional ther- mostat (wall mount or remote control) for the fireplace, your fireplace and blower will not turn on and off at the same time. The fireplace may run for several minutes before the blower turns
2b. Select the MAN (manual) or AUTO button on the
• In manual mode, turn burners on |
or off by pressing the ON or OFF |
buttons on the |
control unit. |
• In auto mode, the room tempera- |
ture is controlled by the thermo- |
stat in the |
Figure 56 - Setting the Selector Switch, Gas Control Knob, and Variable Control Knob for Remote Operation
on. After the heater modulates to the pilot position, the blower will continue to run. The blower will shut off after the firebox temperature decreases.
The blower helps distribute heated air from the fireplace. Periodically check the louvers of the firebox and remove any dust, dirt, or other obstructions that will hinder the flow of air.
trol unit. To increase the room tem- |
perature, press the top arrow of the |
TEMP button. To lower the room |
temperature, press the bottom ar- |
row of the TEMP button. At higher |
settings the heater will run more. |
Shows Temperature Setting
Allows Burners to be Turned On and Off with the
The Heater will Automatically Cycle between Pilot and the Heat Setting that has been Selected.
HI
TEMP
MAN LO ON
AUTO OFF
STATUS
Increases Room Temperature
Decreases Room Temperature
Turns Burners On and Off
Shows Current Operation Mode
Figure 57 - Hand-Held Thermostat Remote Control Unit Selections (GHRCT Only)
26 | 105981 |
