10

OPERATING HEATER

Lighting Instructions

To Turn Off Gas To Appliance

Thermostat Control Operation

Manual Lighting Procedure

OPERATING HEATER

Continued

6.With control knob pressed in, push down and release igni- tor button. This will light pilot. The pilot is attached to the front of burner. The pilot can be seen through the glass panel. If needed, keep pressing ignitor button until pilot lights.

Note: If pilot does not stay lit, refer to Troubleshooting, pages 13 through 15. Also contact a qualified service per- son or gas supplier for repairs. Until repairs are made, light pilot with match. To light pilot with match, see Manual Lighting Procedure.

7.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob.

•If control knob does not pop up when released, contact a qualified service person or gas supplier for repairs.

Note: If pilot goes out, repeat steps 3 through 7. This heater has a safety interlock system. Wait one (1) minute before lighting pilot again.

8.Turn control knob counterclockwise to desired heating level. The main burner should light. Set control knob to any heat level between HI and LO.

CAUTION: Do not try to adjust heating levels by using the equipment shutoff valve.

Ignitor Button

Control Knob

 

TOILP

LO

 

FFO

 

 

HI

 

IGNITOR

 

 

Figure 16 - Control Knob In The OFF Position

Thermocouple

Ignitor Electrode

Pilot Burner

Figure 17 - Pilot

TO TURN OFF GAS

TO APPLIANCE

Shutting Off Heater

1.Turn control knob clockwise to the OFF position.

2.Turn off all electric power to the appliance if service is to be performed.

Shutting Off Burner Only (pilot stays lit)

Turn control knob clockwise to the PILOT position.

THERMOSTAT CONTROL

OPERATION

The thermostatic control used on these models differs from stan- dard thermostats. Standard thermostats simply turn on and off the burner. The thermostat used on this heater senses the room temperature. The thermostat adjusts the amount of gas flow to the burner. This increases or decreases the burner flame height. At times the room may exceed the set temperature. If so, the burner will shut off. The burner will cycle back on when room temperature drops below the set temperature. The control knob can be set to any heat level between HI and LO. Selecting the HI setting will cause the burner to remain fully on without modulating down in most cases.

Note: The thermostat sensing bulb measures the temperature of air near the heater cabinet. This may not always agree with room temperature (depending on housing construction, instal- lation location, room size, open air temperatures, etc.). Fre- quent use of your heater will let you determine your own comfort levels.

MANUAL LIGHTING

PROCEDURE

1.Remove front panel (see Figure 8, page 5).

2.Follow steps 1 through 5 under Lighting Instructions, page 9.

3.With control knob pressed in, strike match. Hold match to pilot until pilot lights.

4.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Follow step 8 under Lighting Instructions.

5.Replace front panel.

For..com

110373-01A

Page 9 Page 11
Page 10
Image 10
Desa REM10PT To Turn OFF GAS To Appliance, Thermostat Control Operation, Manual Lighting Procedure, Shutting Off Heater
Page 9 Page 11

REM10PT specifications

Desa REM10PT, an innovative solution for modern farming, embodies the convergence of advanced technology and sustainable agricultural practices. Recognized for its efficiency and effectiveness, REM10PT serves as a pivotal platform designed to enhance productivity while minimizing environmental impact.

One of the standout features of the Desa REM10PT is its advanced monitoring system. This system utilizes IoT (Internet of Things) technology to provide real-time data on soil conditions, weather patterns, and crop health. By carefully tracking these metrics, farmers can make informed decisions that lead to optimized resource utilization. This capability not only boosts yield but also conserves water and fertilizers, which is crucial in regions facing water scarcity.

Another key characteristic of the Desa REM10PT is its integration of precision agriculture techniques. With GPS-enabled machinery, farmers can apply inputs precisely where needed, reducing waste and increasing efficiency. This technology aligns with the best practices of modern agriculture, ensuring that every inch of land is utilized effectively.

The design of Desa REM10PT emphasizes sustainability. Constructed using eco-friendly materials, it aims to reduce the carbon footprint associated with traditional farming equipment. Furthermore, it promotes practices that enhance soil health, such as reduced tillage and cover cropping, enabling a regenerative approach to farming.

In addition to these features, Desa REM10PT boasts user-friendly software that simplifies data analysis. Farmers can access an intuitive dashboard that aggregates data from various sources, helping them to visualize trends and make swift decisions. This platform also allows for remote monitoring, empowering farmers to manage their operations from anywhere at any time.

Finally, a key component of Desa REM10PT is its emphasis on community and education. The platform is not just a tool; it is a portal for sharing knowledge and best practices among farmers. Through workshops and online resources, it fosters a collaborative environment where users can learn from each other, enhancing the overall agricultural ecosystem.

In summary, Desa REM10PT encapsulates the future of agriculture with its holistic approach, merging advanced technology, sustainability, and community engagement. By adopting such innovative solutions, the agricultural sector moves toward more productive and environmentally responsible practices, ensuring a bountiful future for generations to come.
Top Page Image Contents