Desa S39PT installation manual Installing Optional Blower Accessory GA3650TA, Knob Housing

OWNER’S MANUAL

INSTALLATION

Continued

13.Using the four screws previously re- moved, mount blower assembly to stove by reattaching blower brackets to rear panel (see Figure 15, page 10). Tighten screws securely.

14.Install plastic control knob onto output shaft of speed control housing (see Fig- ure 16). Place speed control housing just inside control compartment door in front of stove (see Figure 17).

15.Using two screws provided in blower kit, mount blower speed control hous- ing to mounting tab in left side of lower control compartment (see Figure 17).

16.Check to make sure that the power cord is completely clear of blower wheel and there are no foreign objects in blower wheel.

17.Carefully replace stove top panel. Align holes and replace six screws removed in step 1, page 10. Slide top trim onto top panel. Attach with 2 screws re- moved in step 1, page 10.

18.Peel off the backing paper and stick the supplied wiring diagram decal on the stove floor as shown in Figure 16.

19.Plug power cord into a convenient 3-prong grounded wall receptacle near the stove.

WARNING: ELECTRICAL GROUNDING INSTRUCTIONS This appliance is equipped with a three-prong (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle.

20.Using speed control knob, turn blower on and check for operation.

21.All remaining parts from blower kit may be discarded.

Blower Speed

Control Housing

Figure17 -InstallingBlowerControlHousing

INSTALLING OPTIONAL BLOWER ACCESSORY GA3650TA

Tools required: Phillips screwdriver

NOTICE: Shut off gas heater during the following blower installation.

1.Remove 2 screws from rear tabs on top trim. Pull trim forward to remove (see Figure 12, page 10).

2.Remove three screws from under top lip on each side of stove to remove top panel (see Figure 12, page 10).

3.Facing front of stove, carefully slide top panel forward until it is completely re- moved from stove (see Figure 12, page 10).

6.Install one plastic bushing provided in blower kit into the 1 1/2" hole in the left rear of firebox floor. Access hole through the rectangular opening in the rear panel (see Figure 13, page 10).

4.Disconnect power cord wires from blower motor (if connected) (see Figure 14, page 10).

5.Disconnect green ground wire from blower housing (if connected) by re- moving screw holding wire terminal (see Figure 14, page 10).

Power

Cord

Wiring

Diagram

Decal

Control	Speed Control
Knob	Housing

Figure 16 - Routing Power Cord

WARNING: Never attempt to service heater while it is plugged in, operating, or hot. Burns and electrical shock could result. Only a qualified service person should service or repair heater.

If any of the original wire as supplied with the appliance must be replaced, it must be replaced with 105° C wire or it’s equivalent.

WARNING: Label all wires prior to disconnection when servicing controls. Wiring errors can cause im- proper and dangerous operation. Verify proper opera- tion after servicing.

Variable

			Fan Switch
	V.A.C.		Off	Black	On
			Black			Motor
110/115						Blower
		Black				Black
		Green
		White				White

120 Vac. 60 Hz. . 78 Amps
DESA International, Bowling Green, KY	101584-05

7.Remove the two blower mounting brackets from the rear panel by remov- ing two screws each (see Figure 15, page 10).

8.Attach the two mounting brackets to blower housing using four screws pro- vided in blower kit (2 for each bracket) (see Figure 15, page 10). Tighten screws securely. Place blower assem- bly temporarily on top of firebox.

9.If screen is installed, carefully lift slightly and pull forward to remove.

10.If logs are installed, carefully remove and set aside.

Continued

107435 11 For more information, visit www.desatech.com