DeWalt DWE46101 Attaching Side Handle ( g.1), Mounting and Removing Mortar Raking Shroud ( g.3), Fitting and Removing a Cutting Disc ( g.1, 4), Mortar Raking Shroud ( g.6)

ENGLISH

Attaching Side Handle (ﬁ g.1)

WARNING: Before using the tool,

check that the handle is tightened

securely.

Screw the side handle (c) tightly into one of the holes

(p) on either side of the gear case.

Mounting and Removing Mortar Raking Shroud (ﬁ g.3)

NOTE: The supplied mortar raking shroud is only

recommended for use with the DWE46101 heavy-

duty mortar raking motor.

1. Open the clamp lever (n) on the tuckpoint

shroud and align the tabs (q) on the tuckpoint

shroud with the slots (r) on the grinder gear

case.

2. With the clamp lever open, rotate the shroud

into the desired working position. The shroud

should be positioned between the spindle and

the operator to provide optimum efficiency.

3. Close the clamp lever (n) to secure the tuckpoint

shroud on the gear case. Do not operate the

grinder with a loose tuckpoint shroud or the

clamp lever in open position.

4. To remove the tuckpoint shroud, open the

clamp lever, rotate the tuckpoint shroud to align

the slots and tabs and pull up on the tuckpoint

shroud.

NOTE: The tuckpoint shroud is pre-adjusted to the

diameter of the gear case hub at the factory. If, after

a period of time, the tuckpoint shroud becomes

loose, tighten the clamp adjusting screw (i) with

clamp lever in the closed position.

NOTICE: Do not tighten the clamp

adjusting screw with the clamp lever in

open position. Undetectable damage to

the tuckpoint shroud or the mounting

hub may result.

NOTICE: If tuckpoint shroud cannot be

tightened by the clamp adjusting clamp,

do not use tool. Take the tool and

tuckpoint shroud to a service center to

repair or replace the tuckpoint shroud.

Fitting and Removing a Cutting Disc (ﬁ g.1, 4)

WARNING: Do not use a damaged

disc.

1. With shroud installed, place the tool on a table,

spindle up.

2. Fit the backing flange (d) correctly onto the

spindle (b) (fig.4).

3. Rotate open the cornering door (m) and place

the cutting disc (u) on the backing flange (d).

4. Screw the threaded clamp nut (e) onto the

spindle (b).

5. Press the spindle lock button (a) and rotate the

spindle (b) until it locks in position.

6. Tighten the threaded clamp nut (e) with the two-

pin spanner supplied.

7. Release the spindle lock.

8. Close and secure the cornering door (m) by

tightening the cornering door locking lever (l).

9. To remove the disc, loosen the threaded clamp

nut (e) with the two-pin spanner.

Mortar Raking Shroud (ﬁ g.6)

WARNING: Only Type 1 diamond

wheels shall be used with tuck-

point shroud. Do not cut metal. Do not

use with bonded abrasive wheels.

Follow the Fitting and Removing a Cutting Disc

instructions and mount the grinding disc.

It may be necessary to open the cornering door

to install 125mm tuckpointing wheels, refer to

Cornering Door Application.

DEPTH OF CUT ADJUSTMENT (FIG.5)

1. Loosen the depth of cut shoe locking knob (k).

2. Slide the depth of cut shoe (j) to the desired

position.

3. Tighten depth of cut shoe locking knob.

CORNER DOOR APPLICATION (FIG.6)

WARNING: To reduce the risk

of injury, ALWAYS turn the tool

off and disconnect the tool from

the power source before making

any adjustments or removing

or installing attachments or

accessories. This applies to both

the grinder and the dust extractor

vacuum. Such preventative safety

measures reduce the risk of starting the

tool accidentally.

WARNING: Risk of personal injury. The

corner door should only be opened for

cutting inside corners. Keep hands and

body away from cutting area at all times.

Ensure corner door is closed in all other

applications.

This feature allows the cutting of an inside corner.

1. Ensure the tool is off and wheel has come to a

complete stop.