Safety Instructions (cont’d), General Information
4
This device incorporates an anticopy process technology that is protected by U.S. patents and other intellectual property rights.The
anticopy process is licensed for non-commercial, home use only. Reverse engineering or disassembly is prohibited.
NOTE TO CATV SYSTEM INSTALLER
Article 820-40 of the NEC (National Electrical Code) provides guidelines for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the building, as close to the point cable entry as practical.
WARNING
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
FCC Regulations and Information
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful inter-
ference to radio or television reception (which you can determine by turning the equipment off and on), you are encouraged to try
to correct the interference by one or more of the following measures:
Reorient or relocate the receiving satellite dish antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT
Any changes or modifications to the equipment by the user not expressly approved by the warranty or manufacturer could void the user’s
authority to operate the equipment.
Domestic use U.S.A – For units used at 120V, use only the power supply cord which is supplied with the product.
ANALOG DEVICE WARNINGS
Federal Communication Commission (FCC) Part 68 and Administrative Council for Terminal Attachments (ACTA)
This device complies with Part 68 of the FCC rules and the requirements adopted by the ACTA.A label on the bottom panel of this
equipment contains, among other information, a product identifier in the format US : AAAEQ##TXXXX. If requested, this number
must be provided to the telephone company. The REN is used to determine the number of devices that may be connected to a
telephone line.Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most,
but not all areas, the sum of RENs should not exceed five (5.0).To be certain of the number of devices that may be connected to a line,
as determined by the total RENs, contact the local telephone company.
The REN for this product is part of the product identifier that has the format US :AAAEQ##TXXXX.The digits represented by ##
are the REN without a decimal point. For the receiver, 0.1 means a REN of 0.1. Note : RENs are associated with loop-start and ground-start
ports. Do not use for E & M or digital ports.
This equipment uses the following USOC jack: RJ-11C. No modular plug is provided with this equipment.
A plug and jack used to connect the receiver to the premises wiring and telephone network must comply with the applicable FCC
Part 68 rules and requirements adopted by ACTA. A compliant telephone cord is provided with this product. It is designed to be
connected to a compatible modular jack that is also compliant. See installation instruction for details.
If the receiver causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance
of service may be required. But if advance notice isn’t practical, the telephone company will notify the customer as soon as possible.
Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.The telephone company may make
changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the tele-
phone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service. If the
equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until
the problem is resolved.
This equipment is of a type that is not intended to be repaired by the user.
This equipment cannot be used on public coin phone service provided by the telephone company. Connection to party line service
is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information.
If your home has specially wired alarm equipment connected to the telephone line,ensure the installation of this receiver does not disable
your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified
installer.
We recommend the installation of an AC surge arrester in the AC outlet to which this equipment is connected.Telephone companies
report that electrical surges, typically lightning transients, are very destructive to customer terminal equipment connected to AC
power sources.
If trouble is experienced with the receiver, for repair or warranty information, please call: 1-800-347-3288.
D10-300-6 27/09/04 17:13 Page 4