Manuals / Dixon / Lawn and Garden / Lawn Mower

Dixon 13088-1100A manual Deck Removal, Care And Maintenance

Models: 13088-1100A

1 40

Download 40 pages 32.82 Kb

Page 28

Image 28

CARE AND MAINTENANCE

DECK REMOVAL:

1.Place cut height lever in lowest cut position.

2.Pull belt idler back to allow belt to be removed from idler pulley and electric clutch pulley.

3.Remove hair pin cotter and washer from one end of deck support cross shaft. Note location of remaining shim washers used between chassis and mower deck plates. Slide shaft from chassis and mower deck.

4.Remove hair pin cotter and washer from each deck L-rod. Remove L-rods from lift arms. At this point, deck will drop down.

5.Carefully raise and support front of chassis. Slide mower deck to either side for removal. (Reverse procedure to reinstall deck assembly).

NOTE: When deck is reinstalled on frame, check that belt is correctly routed in the groves of all pulleys and that belt idler is applying tension to the back side of the belt.

Page 28

Image 28

Dixon 13088-1100A manual Deck Removal, Care And Maintenance, Place cut height lever in lowest cut position

Contents

OperatorsManual 4500SERIES ZTR MOWERS 2001See your dealer for warranty service, parts and repairs IMPORTANT READ CAREFULLYINDEX SAFETYWARRANTY POLICY SPECIFICATIONSSAFETY RIDING LAWNMOWERS, IF IMPROPERLY OPERATEDCAN CAUSE SERIOUS INJURY OR DEATH The most common causes of injury to the operator or bystanderSAFETY SYMBOLS Safety Alert SymbolDanger SAFETYFailure to observe the following safety instructions could result in GENERAL OPERATIONThis cutting mower is capable of amputating hands & feet and throwing objectsSLOPE OPERATION which can result in severe injury or deathAll slopes require extra caution SAFETYNEVER assume children will stay where they were last seen CHILDRENTragic accidents can occur if the operator is not alert to the presence of childrenSERVICE SAFETYDIXON LIMITED WARRANTY POLICY - 4500 SERIES LABOR COSTS. THIS WARRANTY IS SUBJECT TO THE FOLLOWING CONDITIONSDIXON ZTR MOWERS ARE WARRANTED AGAINST DEFECTS IN MATERIALS AND LIMITATIONSSPECIFICATIONS Models ZTR 4515B and 4516KDO NOT operate mower without seat adjustments properly tightened SEAT ADJUSTMENT INSTRUCTIONSPage CONTROLS PARKING BRAKETO SET PARKING BRAKE TRANSMISSION DRIVE SYSTEMTO GO FORWARD TO GO BACKWARDTURNING BRAKINGBLADE DRIVE CIRCUIT BREAKERMOWER DECK CUT HEIGHT LIFT LEVER CONTROLSTOWING OPERATION INSTRUCTIONSBEFORE OPERATING MOWER TESTING OF SAFETY INTERLOCK SYSTEMS OPERATION INSTRUCTIONSEngine should not turn over or attempt to start Engine should not turn over or attempt to startTO FREE WHEEL MACHINE STARTING INSTRUCTIONSOPERATION INSTRUCTIONS MOWING WITH A MULCHING ATTACHMENT OPERATION INSTRUCTIONSMOWING WITH A GRASS CATCHER ATTACHMENT OPERATION INSTRUCTIONSSIDE DISCHARGE OF THE CLIPPINGS GRASS HEIGHT SUGGESTIONSOPERATION INSTRUCTIONS 5. Maintain Sharp Blades Throughout The Cutting SeasonCARE AND MAINTENANCE MAINTENANCE SCHEDULEMOWER BLADE MAINTENANCE CARE AND MAINTENANCEBELT TENSION CARE AND MAINTENANCEManual adjustment. Refer to illustration below Auto tensioner with spring loaded idler. No adjustment requiredCARE AND MAINTENANCE FORWARD TRAVEL SPEED ADJUSTMENT1. Drive machine until hydrostats have warmed up NEUTRAL ADJUSTMENT CARE AND MAINTENANCEMOWER DECK LEVELING PROCEDURE CARE AND MAINTENANCECARE AND MAINTENANCE DECK REMOVAL1. Place cut height lever in lowest cut position CHANGING THE ENGINE OIL CARE AND MAINTENANCEOIL FILL PLEASE DISPOSE OF USED OILS AT PROPER COLLECTION CENTERSBRAKE SYSTEM LUBRICATIONCARE AND MAINTENANCE CARE AND MAINTENANCE WHEELS AND TIRESSTANDARD SERVICE PARTS LIST TROUBLESHOOTING MOWER CUT QUALITYDRIVE SYSTEM TROUBLESHOOTINGTROUBLESHOOTING ELECTRICAL SYSTEMHave electrical system checked by your dealer Page Page Page Name OWNER INFORMATIONAddress 4500 Series 4515B&4516K Part No. 13088-1100A Dixon and ZTR are registered trademarks of Dixon Industries, IncDIXON INDUSTRIES, INC