Manuals / Dixon / Lawn and Garden / Lawn Mower

Dixon 13091-0500, ZTR 7025 manual Mower Blades, V-Belts, Care And Maintenance

Models: 13091-0500 ZTR 7025

1 40

Download 40 pages 42.51 Kb

Page 25

MOWER BLADES:

CARE AND MAINTENANCE

Stop engine, remove ignition key and spark plugs for safety. Wear CAUTION heavy, thick gloves when holding onto cutter blade, avoid the sharp

edge of the blade.

MOWER BLADES:

Check sharpness of mower blades after every 10 hours of operation. To sharpen blades, proceed as follows.

A.Remove bolt, lock washer, and cup washer mounting blade on shaft. Remove blade.

B.Blades should be discarded when worn excessively.

C.Sharpen blade with a hand file, electric grinder or blade sharpener. Wear gloves and eye protection when sharpening. Grind blade at original 25 degree bevel.

D.Check balance of blade by positioning the blade on a nail or blade balance pedestal. Grind the blade on the end that is heavier until both sides balance.

E.Install blade, cup washer, lock washer and bolt. Make sure to tighten bolt to 60 ft. lbs.

DANGEROUS!

DO NOT USE

BLADE IN THIS

CONDITION!

New Blade

25 degrees	When notch starts,
	discard blade

V-BELTS:

There are 3 V-Belts on your Dixon Zero Turning Radius Mower. They should be checked every 50 hours. Replace any belts found to be in poor condition. All belts are equipped with spring loaded belt tighteners and do not require tightening adjustments.

Page 25

Image 25

Dixon 13091-0500, ZTR 7025 manual Mower Blades, V-Belts, Care And Maintenance

Contents

7000 SERIES ZTR MOWERS Operators Manual2001 IMPORTANT - READ CAREFULLY SAFETY INDEXWARRANTY POLICY SPECIFICATIONSRIDING LAWNMOWERS, IF IMPROPERLY OPERATED SAFETYCAN CAUSE SERIOUS INJURY OR DEATH The most common causes of injury to the operator or bystanderSAFETY DangerSafety Alert Symbol Follow recommended safety precautions and safe operating practicesSAFETY GENERAL OPERATIONFailure to observe the following safety instructions could result in This cutting mower is capable of amputating hands & feetwhich can result in severe injury or death SLOPE OPERATIONAll slopes require extra caution SAFETYCHILDREN NEVER assume children will stay where they were last seenTragic accidents can occur if the operator is not alert to the presence of childrenSAFETY SERVICELABOR COSTS. THIS WARRANTY IS SUBJECT TO THE FOLLOWING CONDITIONS DIXON LIMITED WARRANTY POLICY - COMMERCIAL MODELSDIXON ZTR MOWERS ARE WARRANTED AGAINST DEFECTS IN MATERIALS AND LIMITATIONSDual Element Air Cleaner SPECIFICATIONSWeight Folded sheet metal2. Slide seat forward or backward 3. Release seat slide adjuster 1. Grasp seat slide adjuster and move it into adjustment positionModel SEAT ADJUSTMENT INSTRUCTIONSBlade Clutch Switch Ignition Key Throttle CONTROLSCut Height Adjustment Lever Cut Height Stop Pin Steering Control Levers Choke Parking Brake LeverCONTROLS PARKING BRAKEEngage parking brake before starting engine Allows the mower to turn on its own axis zero turning radiusTO GO FORWARD CONTROLSTO GO BACKWARD TURNINGControls the cutting height Seven positions of adjustment To engage blades Pull up on the switch To disengage blades Push downCONTROLS Located on control panel, on operators rightBEFORE OPERATING MOWER OPERATION INSTRUCTIONSBLADE DRIVE SWITCH TEST Electric Clutch TESTING OF SAFETY INTERLOCK SYSTEMSDo not operate mower if safety switches are not operating properly OPERATION INSTRUCTIONSSTARTING INSTRUCTIONS Cold Engine OPERATION INSTRUCTIONSOPERATION INSTRUCTIONS Always turn engine off when leaving mowerSTARTING INSTRUCTIONS OPERATION INSTRUCTIONS Be sure that deflector is properly installed on the discharge chuteGRASS HEIGHT SUGGESTIONS 5. Maintain Sharp Blades Throughout The Cutting SeasonOPERATION INSTRUCTIONS TO FREE WHEEL MACHINE UNLOCK TRANSMISSIONMAINTENANCE SCHEDULE CARE AND MAINTENANCEBATTERY CARE AND MAINTENANCEBattery electrolyte is a poisonous and corrosive sulfuric acid solution. Avoid spilling on skin, eyes and clothingV-BELTS MOWER BLADESCARE AND MAINTENANCE CHECKING & REPLENISHING OIL IN HYDROSTATIC TRANSMISSION LUBRICATIONCARE AND MAINTENANCE Dirt or water in oil can ruin the hydrostatic transmissionsCARE AND MAINTENANCE PARKING BRAKE ADJUSTMENTHYDROSTATIC TRANSMISSIONS HYDROSTAT DRIVE BELT REPLACEMENT PROCEDURECARE AND MAINTENANCE CARE AND MAINTENANCE STEERING CONTROL ADJUSTMENTSCARE AND MAINTENANCE STEERING CONTROL ADJUSTMENTS continuedCARE AND MAINTENANCE LEVELING THE DECKPROCEDURE FOR RAISING AND LOWERING THE DECK FOR SERVICING CARE AND MAINTENANCECut Height Adjustment Pin Cut Height Adjustment Lever Locking Pin CARE AND MAINTENANCEDeck Latch Foot Deck Center Deck Spindle Deck Lift Bolt Rear Deck Mounting Latch Front Caster Wheels positioned outMODEL ZTR STANDARD SERVICE PARTS LISTKOHLER AIR AND OIL FILTER PART NUMBERS check TROUBLESHOOTINGvent add oilCheck spark plug or condition and TROUBLESHOOTINGCheck and re-gap Add oilPage Page DATE PURCHASED MOWER MODEL NUMBER MOWER SERIAL NUMBER PURCHASED FROM OWNER INFORMATIONDATE OIL CHANGED DATE ENGINE TUNEDDIXON INDUSTRIES, INC Dixon and ZTR are registered trademarks of Dixon Industries, Inca BLOUNT International Inc. Co PO Box