Lubrication, Care And Maintenance | Dixon ZTR 7025, 13091-0500

LUBRICATION:

CARE AND MAINTENANCE

LUBRICATION:

A.Engine: Follow engine manufacturer's recommendation.

B.Deck spindles: Lubriacte with 3 "shots" only, every 100 hours.

C.Hydrostatic transmission and filter (follow instructions listed below).

Dirt or water in oil can ruin the hydrostatic transmissions.

CHECKING & REPLENISHING OIL IN HYDROSTATIC TRANSMISSION

Check the oil level in hydrostatic transmission oil reservoir after every 25 hours of usage. Clean the oil reservoir cap and the area around it prior to removal. Check the oil level on the dipstick. The proper oil level should register between the marked hole on the dipstick and the end of the dipstick. Replenish as needed with 20W-50 Motor Oil. DO NOT OVERFILL. When checking the oil level, be very careful to keep the reservoir clean.

Change the oil in the reservoir and hydrostat transmission oil filter after the first 100 hours of use. Then every 500 hours after that. Remove the filter and be sure all oil has drained from the reservoir. Replace with new filter and 20W-50 Mobil Super II.

Oil Reservoir Cap

Dipstick

Fuel Cap

Please dispose of used oil at proper collection centers - protect your environment

Page 26

Image 26

Dixon ZTR 7025, 13091-0500 manual Lubrication, Checking & Replenishing Oil In Hydrostatic Transmission, Care And Maintenance

Contents

2001 Operators Manual7000 SERIES ZTR MOWERS IMPORTANT - READ CAREFULLY WARRANTY POLICY INDEXSAFETY SPECIFICATIONS CAN CAUSE SERIOUS INJURY OR DEATH SAFETYRIDING LAWNMOWERS, IF IMPROPERLY OPERATED The most common causes of injury to the operator or bystander Follow recommended safety precautions and safe operating practices DangerSafety Alert Symbol When you see this symbol BE ALERT to the potential for injury This cutting mower is capable of amputating hands & feet GENERAL OPERATIONFailure to observe the following safety instructions could result in and throwing objects All slopes require extra caution SLOPE OPERATIONwhich can result in severe injury or death Tragic accidents can occur if the operator is not alert to the NEVER assume children will stay where they were last seenCHILDREN presence of children SERVICE DIXON ZTR MOWERS ARE WARRANTED AGAINST DEFECTS IN MATERIALS DIXON LIMITED WARRANTY POLICY - COMMERCIAL MODELSLABOR COSTS. THIS WARRANTY IS SUBJECT TO THE FOLLOWING CONDITIONS AND LIMITATIONS Weight SPECIFICATIONSDual Element Air Cleaner Folded sheet metal Model 1. Grasp seat slide adjuster and move it into adjustment position2. Slide seat forward or backward 3. Release seat slide adjuster SEAT ADJUSTMENT INSTRUCTIONS Cut Height Adjustment Lever Cut Height Stop Pin CONTROLSBlade Clutch Switch Ignition Key Throttle Steering Control Levers Choke Parking Brake Lever Allows the mower to turn on its own axis zero turning radius PARKING BRAKEEngage parking brake before starting engine Each lever controls one side of the mower TURNING TO GO FORWARDTO GO BACKWARD BRAKING Located on control panel, on operators right To engage blades Pull up on the switch To disengage blades Push downControls the cutting height Seven positions of adjustment Located to the right and front of operator OPERATION INSTRUCTIONS BEFORE OPERATING MOWER Do not operate mower if safety switches are not operating properly TESTING OF SAFETY INTERLOCK SYSTEMSBLADE DRIVE SWITCH TEST Electric Clutch 1. The mower blades must be disengaged before the engine will start STARTING INSTRUCTIONS Cold Engine Always turn engine off when leaving mower STARTING INSTRUCTIONS 5. Maintain Sharp Blades Throughout The Cutting Season Be sure that deflector is properly installed on the discharge chuteGRASS HEIGHT SUGGESTIONS Correct mowing height can reduce weeds and disease by 50% to 80% TO FREE WHEEL MACHINE UNLOCK TRANSMISSION CARE AND MAINTENANCE MAINTENANCE SCHEDULE acid solution. Avoid spilling on skin, eyes and clothing BATTERYBattery electrolyte is a poisonous and corrosive sulfuric ENGINE MOWER BLADES V-BELTS Dirt or water in oil can ruin the hydrostatic transmissions LUBRICATIONCHECKING & REPLENISHING OIL IN HYDROSTATIC TRANSMISSION PARKING BRAKE ADJUSTMENT HYDROSTAT DRIVE BELT REPLACEMENT PROCEDURE HYDROSTATIC TRANSMISSIONS STEERING CONTROL ADJUSTMENTS STEERING CONTROL ADJUSTMENTS continued LEVELING THE DECK PROCEDURE FOR RAISING AND LOWERING THE DECK FOR SERVICING Rear Deck Mounting Latch Front Caster Wheels positioned out Cut Height Adjustment Pin Cut Height Adjustment Lever Locking PinDeck Latch Foot Deck Center Deck Spindle Deck Lift Bolt of the way KOHLER AIR AND OIL FILTER PART NUMBERS STANDARD SERVICE PARTS LISTMODEL ZTR vent TROUBLESHOOTINGcheck add oil Add oil Check spark plug or condition andCheck and re-gap Put in lock position see pg Page Page DATE OIL CHANGED OWNER INFORMATIONDATE PURCHASED MOWER MODEL NUMBER MOWER SERIAL NUMBER PURCHASED FROM DATE ENGINE TUNED a BLOUNT International Inc. Co Dixon and ZTR are registered trademarks of Dixon Industries, IncDIXON INDUSTRIES, INC PO Box