9.TESTING LP GAS SAFETY SHUTOFF

The gas safety shutoff must be tested after the refrigera- tor is connected to LP gas supply.

To test the gas safety shutoff, proceed as follows:

A. Start the refrigerator according to the instructions for LP Gas Operation. See "Section C. Operation Instructions."

B.Check that the gas flame is lit. Allow it to burn a few minutes to ensure a full, stable flame.

C.Turn the gas safety valve (D, FIG. 8) to the "OFF" position. Within 1-2 minutes the gas safety device within the valve should automatically close. An audible "click" from the valve may be heard.

D.Turn the gas safety valve to the "ON" position (D, FIG. 8).

E.Without pushing in the knob (D, FIG. 8) of the gas safety device, apply a commercial leak detection solution to the burner jet. No bubbles should appear. Bubbles indicate a gas leak and the safety valve must be replaced by a qualified serviceman.

F.Rinse the burner jet with water. Light the burner and allow it to burn for five minutes.

10.120 VOLT AC ELECTRICAL CONNECTION

The refrigerator is equipped with a three-prong (groun- ded) plug for protection against shock hazards, and should be plugged directly into a properly grounded three-prong receptacle. DO NOT cut or remove the gro- unding prong from this plug. The power cord should be routed to avoid direct contact with the burner cover, fuel cover or manual gas shutoff valve knob.

11. 12 VOLT DC CONNECTION

The 125 watt heating element operates the cooling unit when the refrigerator is connected to the battery of the vehicle. It has a current rating of about 10.5 amps; there- fore, the wiring from the battery to the refrigerator must be of heavy enough gauge to carry this load satisfactori- ly without undue voltage drop. To ensure this, the mini- mum size of wire to be used is 14 A.W.G. The terminal block for connecting the 12V supply cable to the battery is positioned at the lower lefthand corner of the rear side (G, FIG. 8). From this terminal, the connection to the battery should be made using ring-type clamps with tightening bolts to ensure good contact with the battery terminals. Polarity is not important, therefore it does not matter which wire leads to which battery terminal.

DO NOT connect lights or any other electrical com- ponents to the same circuit that is used by the refri- gerator.

IMPORTANT:

To prevent the refrigerator from being left on and draining the battery when the vehicle's engine is not running and charging the battery, it is recommended that an automatic cutout relay be installed between the battery and the refrigerator toggle switch so that the refrigerator will not draw current when the vehicle ignition is switched off. Alternatively, a suita- ble plug and receptacle should be installed in the 12V supply line so that the refrigerator can be dis- connected from the supply, as necessary.

FUSE

A 12 amp (continuous rating) fuse should be incorpora- ted in the wiring of the DC supply, as near to the battery as possible. The fuse must be in the side of the wiring which is not connected to the chassis. For example, if the vehicle has a negative ground, the fuse must be in the positive side of the wiring.

12.CHANGING DOOR HINGES FROM ONE SIDE TO THE OTHER

If required, the door hinges can be moved to the opposi- te side. Reverse the door hang in the following way:

A.Unscrew the upper hinge pin, taking care not to lose the set of washers and bushings.

B.Lift the door from the lower hinge pin. If decorative door panel is to be installed, proceed to Step 13.

C.Unscrew the pin and mount it on the opposite side hinge.

D.Unscrew the travel catch and mount it on the opposite side.

E.Change the cover plate and travel lock plate in top of door frame to opposite side. Use a screwdriver to press down on one edge of the cover plate. The opposite edge will rise above the frame. Use a knife blade under the raised edge to pop it out. See FIG. 7.

Use needle-nosed pliers to carefully lift lock plate out of door frame. See FIG. 7.

F.Replace door on lower hinge pin. Replace upper hinge pin and bushings removed in Step A.

G.Check that the door closes properly and seals all around.

FIG. 7

6

Page 5 Page 7
Page 6
Image 6
Dometic RM 4223 Testing LP GAS Safety Shutoff, Volt DC Connection, Changing Door Hinges from ONE Side to the Other, Fuse
Page 5 Page 7

RM 4223 specifications

The Dometic RM 4223 is a prominent absorption refrigerator designed to cater to the needs of campers, RV enthusiasts, and those who enjoy the great outdoors. Renowned for its reliability and efficient cooling capabilities, this model exemplifies modern advancements in portable refrigeration technology.

One of the standout features of the Dometic RM 4223 is its remarkable cooling performance. Utilizing a proven absorption cooling system, it operates quietly and efficiently, providing consistent cooling without the noise commonly associated with traditional compressor refrigerators. This makes it an ideal addition to any RV or camper where serenity is paramount.

With a capacity of approximately 3.6 cubic feet, the RM 4223 has ample space to accommodate essential food items and beverages for your trips. The interior design includes adjustable shelving, allowing users to customize the layout to suit their storage needs. This flexibility ensures that everything from larger bottles to smaller items can be neatly arranged.

The Dometic RM 4223 is designed for versatility, featuring three power source options: 12V DC, 110V AC, and propane. This multi-power capability ensures that whether you’re on the road, in a campsite, or off-grid, you'll have reliable refrigeration at your fingertips. Switching between power sources is seamless, providing users with the freedom to choose the most convenient option.

Another significant characteristic of the RM 4223 is its robust build quality. Built to withstand the rigors of travel, this refrigerator is constructed with high-quality materials that ensure durability. It also boasts a sleek design that fits well with the aesthetic of modern RV interiors.

Efficiency is a core attribute of the Dometic RM 4223. With its energy-saving technology, it minimizes power consumption, making it an environmentally friendly choice. Users can rest easy knowing they’re making a sustainable option while enjoying the comforts of home on the road.

Finally, the compact dimensions of the RM 4223 make it easy to install in various spaces without sacrificing valuable room. This model combines functionality with user-friendly operation, making it a popular choice for those who prioritize comfort and convenience during their travels. In summary, the Dometic RM 4223 is a reliable, efficient, and versatile refrigerator that enhances the camping and RV experience, featuring advanced cooling technology, multiple power options, and a commitment to durability.
Top Page Image Contents