Manuals / Drolet / Household Appliance / Stove

Drolet 45521A owner manual The Advantage Of Installing A Blower Fan

Models: 45521A

1 40

Download 40 pages 46.6 Kb

Page 29

2.6 THE ADVANTAGE OF INSTALLING A BLOWER (FAN)

2.6 THE ADVANTAGE OF INSTALLING A BLOWER (FAN)

A blower can be installed at the back of your DROLET stove. This option is necessary if you wish to redistribute into a room the heat trapped at the back of your stove. By forcing hot air toward the front, the blower enables you to extend the radiation power of your stove.

You can purchase this option through your DROLET dealer. Make sure to specify this part number: #AC02050. You can also install a thermodisc to enable the blower to start or stop automatically when the stove is hot or too cold. The thermodisc part number is. Installation instructions are supplied with the blower and the thermodisc.

FIGURE 2.5 The advantage of installing a blower (fan)

29

Image 29

Drolet 45521A owner manual The Advantage Of Installing A Blower Fan, 5 The advantage of installing a blower fan

Contents

READ AND KEEP THIS MANUAL FOR REFERENCE ROCKET E.P.A. WOOD STOVEOWNER’S MANUAL STOVE BUILDER INTERNATIONAL INCCAUTIONS REGISTER YOU WARRANTY ONLINEINTRODUCTION DROLET LIMITED LIFETIME WARRANTY TABLE OF CONTENTSSECTION 1.0 - INSTALLATION SECTION 4.0 MAINTENANCE1.1 GENERAL INSTALLATION SECTION 1.0 - INSTALLATIONCAUTIONS WARNINGS1.3 CLEARANCES TO COMBUSTIBLES AND FLOOR PROTECTOR 1.2 POSITIONING THE STOVEClearances to combustible materials A B C D E F K LFIGURE 1.3 Clearances to combustible materials and floor protection Floor protector Reduced clearances using shieldingFLOOR PROTECTOR CANADAsee graphic Reducing Clearances With ShieldingTYPE OF PROTECTION B- 20 in. 500 mm minimum C- 1 in. 25 mm minimum GraphicD- Between 1 in. and 3 in. 25 mm and 75 mm E- 3 in. 75 mm minimum F- 18 in. 457 mm minimum 1- Shielding 2- Non-combustible spacersA- 1 in.25 mm minimum 1- Combustible wall 2- Non-combustible spacers GraphicGraphic GraphicA- 1 in. 25 mm minimum 1- Combustible wall 2- Non-combustible spacers Graphic3- Brick Graphique2.1 DEFINITIONS SECTION 2.0 CHIMNEY FLUE SYSTEM2.2 CHIMNEY CAUTIONSDo not connect your stove to a chimney serving another appliance Wall support system 2.2.1 Step by step installation of your factory-built chimneyChimney FIGURE 2.2 Minimum Height of the ChimneyStove pipe FIGURE 2.2.1 A Typical installation through the wallTypical installation through the wall Page Page Stove pipe Ceiling support systemChimney Typical installation through the ceiling FIGURE 2.2.1 B Typical Installation Through the Ceiling2. Before you install the ceiling support, you need to frame the area Page « CHIMNEY CONNECTOR» Masonry Chimney 2.2.2 Typical installation through an existing masonry chimneyFIGURE 2.2.2 A Typical Installation Through an Existing FIGURE 2.2.2 B Factory Built Thimble FIGURE 2.2.2 C Brick Thimble FIGURE 2.3 A Connecting Sections 2.3 CHIMNEY CONNECTORFIGURE 2.4 The use of elbows FIGURE 2.3 B Minimum Slope2.5 OUTSIDE COMBUSTION AIR 2.4 DRAFTFIGURE 2.5 The advantage of installing a blower fan 2.6 THE ADVANTAGE OF INSTALLING A BLOWER FANSECTION 3.0 OPERATION 3.1 SAFETY INFORMATIONKeep these instructions for future reference WARNINGS NFPA 211 USADo not elevate the fire by means of grates TABLE 3.2 Energy yield for wood species 3.2 FUELWood species Energy yield3.3 NOTES ABOUT FIRST FIRING 3.2.1 The use of manufactured logs3.2.2 Simple wood moisture test FIGURE 3.1 Air control 3.4 LIGHTING A FIRE3.6 FAN BLOWER OPERATION 3.5 MAINTAINING THE FIRE4.1 CLEANING AND PAINTING YOUR STOVE SECTION 4.0 MAINTENANCE4.2 GASKETING 4.3 ASH REMOVAL4.5 DEALING WITH A CHIMNEY FIRE 4.4 CHIMNEY FLUE CLEANING5.1 ROCKET STOVE SECTION 5.0 FEATURESPART # WARRANTY APPLICATION DROLET LIMITED LIFETIME WARRANTYDESCRIPTION LABOUR