Chapter 1: Setup and Connections

Install Batteries in the Remote

1.Remove the battery compartment cover on the back of the remote.

2.Insert new batteries. Match the polarities (+ and –) on the batteries with the diagram on the remote.

3.Put the battery compartment cover back on the remote.

Important Battery Information

If you’re not going to use the remote for a month or more, be sure to remove the batteries because they can leak and cause damage.

Dispose of batteries in the proper manner, according to federal, state, and local regulations.

Any battery may leak electrolyte if mixed with a different battery type, if inserted incorrectly, if all batteries are not replaced at the same time, if disposed of in fire, or if an attempt is made to charge a battery not intended to be recharged.

Discard leaky batteries immediately. Leaking batteries can cause skin burns or other personal injury.

Point the Remote in the Right Direction and Put it in DVD Mode

When you want the remote to operate the Digital Media Recorder, point the remote at the Digital Media Recorder, not the TV. The remote has to be pointed in the correct direction and toward the correct component in order for the remote control’s signal to communicate with the sensor on the component. Make sure there is a clear path between the remote control and the component you want to operate, so the signal isn’t blocked.

Make sure the remote is in DVD mode — press the DVD button.

Turn on the TV and Digital Media Recorder

1.If you have an RCA, GE, or Proscan TV, press the TV button on the remote and then press the INPUT button on the remote (the TV turns on and tunes to the correct Video Input Channel).

If you have another brand of TV, turn on the TV and tune the TV to the correct Video Input Channel (if you don’t know how to access the Video Input channel on your TV, go to page 16 for help).

Note: You can program your remote to operate most brands of remote controllable TVs. Instructions are on page 19.

2. Press the DVD button on the remote control to put it in the correct mode, and turn on the Digital Media Recorder.

Left arrow button

Down arrow button

DVD

ON • OFF

TV

VCR

AUDIO

AUX

SAT • CABLE

MUTE

 

 

ANGLE

 

CH +

 

 

VOL

 

 

VOL

 

CH -

 

 

ZOOM

 

 

GO BACK

GUIDE

 

 

INFO

 

OK

 

 

MENU

 

 

CLEAR

1 2 3

4 5 6

7 8 9

AGAINADVANCE 0

Up arrow button

Right arrow button

OK button

Complete the Interactive Setup

The next few pages step you through the series of screens that will appear the first time you turn on your Digital Media Recorder.

Use the remote control to follow the on-screen instructions. The arrow buttons move the on-screen highlight in the corresponding directions on the screen (up, down, left, right).

Press the OK button to select a highlighted item.

Notes:

You can access the setup screens from the main menu. If you move, get a different program provider for TV shows, or change your connections, you’ll need to complete the Interactive Setup again.

If you don’t see the Language selection screen (below) the first time you turn on the Digital Media Recorder, make sure you’ve tuned your TV to the Video Input Channel that corresponds to the way you’ve connected the TV to the Digital Media Recorder. If you need help, go to page 16.

REVERSE PLAY FORWARD

Use the arrow buttons on the remote to move through on-screen menus and highlight different options. Press the OK button to select a menu item that is highlighted.

1) Select on-screen menu language

Make sure the remote is in DVD mode (press the DVD button). If you want the on-screen menus to appear in English, press the OK button on the remote control. If you prefer another language, press the arrow down button until that language is highlighted. Press OK to select the language.

Note: If you don’t see the Language selection screen the first time you turn on the

Digital Media Recorder, make sure you’ve tuned your TV to the Video Input

Channel that corresponds to the way you’ve connected the TV to the Digital Media

Recorder. If you need help, go to page 16.

12

Page 14
Image 14
RCA DRC7005N Install Batteries in the Remote, Turn on the TV and Digital Media Recorder, Complete the Interactive Setup