T2000WD/1
HIGH LEVEL |
| LOW LEVEL INPUTS: | |||
INPUT: |
| Low level inputs with a | |||
Speaker level |
| range of 0.2V to 7V RMS. | |||
inputs | with a |
| This is where the front and | ||
range | of 0.5V |
| rear RCA outputs from your | ||
to 17V RMS. |
| head unit or other devices | |||
|
|
| are inserted. | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SUBSONIC FILTER:
For the vast majority of vehicles, peaks or dips occur at about 40Hz – around the frequency of a low bass guitar note. Use this control to correct that peak or dip.
LEVEL ADJUST:
Allows the amplifier to deliver a controlled maximum sound level into selected channel(s) when the volume is turned to max. This acts as a volume limiter for the system, preventing you from over driving the speakers or subwoofers.
AUTO ON RESET REMOTE ON |
R C A l i n e |
| PHASE SHIFT: |
| AUTO SIGNAL |
| LOW PASS FILTER (LPF): |
| 0 - 10dB |
| REMOTE SUB LEVEL: | ||||
t h r o u g h t o |
| This 0 - 180° phase |
| SENSING: |
| This 50Hz - 300Hz low- |
| BASS |
| Allows you to limit the | ||||
c a s c a d e |
| shift | adjustment is |
| Please | refer to |
| pass filter blocks unwanted |
| BOOST |
| amplifier’s bass | output | |
a n o t h e r |
| for | reversing | the |
| p a g e | 3 f o r |
| h i g h f r e q u e n c i e s f o r |
| CONTROL |
| from a location of your | |
amplifier. |
| phase output | with |
| explanation of this |
| cleaner |
|
|
| choice. Using a | screw | ||
N o X o v e r |
| respect to its input. |
| feature. |
|
|
|
|
|
| mounted remote control. | |||
point. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SUB |
|
|
XOVER |
|
|
SETTING |
|
|
50Hz | 70Hz | 150Hz 210Hz 240Hz 300Hz |
POWER LED:
When LED is on, it indicates that the amplifier is ON and f u n c t i o n i n g properly.
The gain knob is not a volume
control. It is designed to match the input level of the amp to the output level of the source unit. Over driving "clipping" the input stage of the amp will cause damage to the amplifier (please refer to table for setting).
MAX INPUT
VOLTAGE
BEFORE
CLIPPING
RCA LEVEL
SPEAKER
LEVEL
7.0V 4.0V 2.5V
17.0V 10.0V 5.0V
1V
1V
AUTO ON RESET REMOTE ON |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| PROTECTION (PROT) LED: |
|
|
|
|
|
| To battery positive (+) |
|
| Two |
| ||||||||||||
|
|
| ||||||||||||||||||||||
| If LED comes on then you have an |
|
|
|
|
|
|
|
|
|
|
| 30A |
| ||||||||||
| issue that requires service. Turn |
|
|
|
|
|
| To remote turn on / trigger |
|
| fuses |
| ||||||||||||
| off the amplifier and call |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
| ||||||||||||||
|
|
|
|
|
|
|
|
|
|
| ||||||||||||||
| Earthquake for further assistance. |
|
|
|
|
|
| To car chassis / ground |
|
|
|
|
|
| ||||||||||
| See warranty for details. |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
| ||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
AUTO ON RESET REMOTE ON |
12 |
|
| 13 |
Specifications Are Subject To Change Without Notice | www.earthquakesound.com |
