EAW KF695z specifications Dimensional Drawing Specifications, Inches Millimeters, Pounds Kilograms

SPECIFICATIONS KF695z

DIMENSIONAL DRAWING

A & E SPECIFICATIONS

1.	SYMBOL	INDICATES 3.00	X	1.35 FLYTRACK.
2.	SYMBOL	INDICATES MOUNTING		POINT,
	3/8-16 THREADED HOLE (FLYTRACK)
3.	SYMBOL	INDICATES CENTER	OF BALANCE.

(12.81)	A
CL
12.25	20.62
5.94	10.00
14.25	A
20°

TOP

DIMENSIONS APPLY

TO TOP & BOTTOM

.

19.75 T.S.C.

33.25

GRILLE PARTIALLY SHOWN

FRONT

The three-way full range loudspeaker system shall incorporate a 15-in LF transducer, a 10-in cone MF transducer and a 1.4- in exit compression driver HF transducer.

The LF driver shall be mounted in a vented enclosure tuned for optimum low frequency response. The MF driver shall be loaded into a midrange horn constructed of 3mm birch ply- wood reinforced with high density polyurethane foam. The MF horn shall incorporate a phase/displacement plug. The HF driver shall be loaded on a constant directivity horn with a nominal coverage pattern of 90° (h) x 45° (v). An internal passive filter network shall provide system equalization and fourth order acoustical crossover between the low and mid frequency sections in bi-amped mode .

System frequency response shall vary no more than ±3 dB from 65 Hz to 17 kHz measured on axis. In bi-amped mode, the low/mid section shall produce a Sound Pressure Level (SPL) of 100 dB SPL on axis at 1 meter with a power input of 1 Watt, and shall be capable of producing a peak output of

ACCESS PANEL

	CL
	INPUT
28.98
	16.75
2.13	BACK

509098 (1) 6/19/01

	8.25	2X 6.44
		4X HANDLE
	6.05
	22.42
		28.98
8.00	2X 8.75
10.08

4.50 14.58

VIEW A-A 2.13

DIMENSIONS APPLY

TO BOTH SIDES

134.5SPL on axis at 1 meter. It shall handle 700 Watts of amplifier power (continuous) and shall have a nominal impedance of 8 Ohms. The HF section shall produce a Sound Pressure Level (SPL) of 110 dB SPL on axis at 1 meter with a power input of 1 Watt, and shall be capable of producing a peak output of 138 SPL on axis at 1 meter. It shall handle 160 Watts of amplifier power (continuous) and shall have a nom- inal impedance of 8 Ohms.

In tri-amped mode, the low frequency and high frequency sec- tions shall meet all bi-amped mode performance criteria. In addition, the midrange frequency section in tri-amped mode shall produce a Sound Pressure Level (SPL) of 109 dB SPL on axis at 1 meter with a power input of 1 Watt, and shall be capable of producing a peak output of 141 SPL on axis at 1 meter. It shall handle 400 Watts of amplifier power (continu- ous) and shall have a nominal impedance of 8 Ohms.

Manufacturing tolerances are +/- 0.13 and +/- 1°

PHYSICAL continued

Dimensions	Inches	Millimeters
Height	33.3	845
Width (front)	19.8	502
Width (rear)	12.9	328
Depth	20.6	524
Trapezoid Angle	10 Degrees per Side

Weights	Pounds	Kilograms
Net Weight	135.0	61.4
Shipping Weight	142.0	64.6

The loudspeaker enclosure shall be trapezoidal in shape. It shall be constructed of multi-ply, void-free cross-grain-lami- nated Baltic birch plywood and shall employ extensive inter- nal bracing. It shall be finished in wear-resistant textured black paint. Input connectors shall be 2x Neutrik NL4 Speakon and 2 x Neutrik NL8 Speakon. The system shall include a switch allowing it to be operated in bi-amp or tri- amp powering mode. A total of six 3-position flytracks with integral 3/8"-16 threaded mounting point (3 each top and bottom) shall be provided. The front of the loudspeaker shall be covered with a powder coated perforated steel grille backed with open cell foam to protect against dust.

The three-way full range loudspeaker shall be the EAW model KF695z.

One	Main Street, Whitinsville, MA 01588	508 234 6158	Toll Free 800 992 5013	FAX 508	234 8251	info@eaw.com	www. eaw. com
EAW	products are continually improved. All specifications are therefore subject to change without notice.			KF695z/2	pp	October 2001	Printed in USA