Eclipse - Fujitsu Ten CD8445 169

How to use the remote control

●Be extremely careful not to swallow the battery.

●The battery life is approximately one year. If the remote control unit does not operate correctly or if the button lamp gets dim, replace the batteries.

●Be sure to orient the batteries correctly so that the positive and negative poles match the diagram.

●Do not use one new battery and one old one; use two new batteries.

●Use only two of the same kind of battery.

●If any liquid is seen leaking from the batteries, remove both batteries and dispose of them properly. Thoroughly clean the battery compartment with a dry cloth. Then install new batteries.

169

Contents

OWNER'S MANUAL Warning Page Page Page Page Page Page How to operate the AREA SHOT function (U.S.A. only) How to operate the tuner with an optional HD RADIO tuner connected (U.S.A. only) How to operate the tuner with an optional SIRIUS satellite radio tuner Page Page Page How to operate the AREA SHOT function (U.S.A. only) How to operate the receiver with an optional CD changer How to operate the tuner with an optional HD Radio tuner How to operate the tuner with an optional SIRIUS satellite Page Notes on operation About compact discs About brand new CDs About CD accessories ●Do not use accessories About cleaning a CD About Memory Sticks ●It may not be possible to use MG Memory Sticks that have just been purchased. If this happens, use the unit ●Do not use Memory Sticks with labels that are peeling off or that have name tags (labels) attached ●Store Memory Sticks in places away from direct sunlight About cleaning the Memory Sticks Front view With the front open About ESN ESN can be set or cancelled using any of the following methods: •Key CD security (See page 26) •Memory Stick security (See page 30) •ACC security (See page 38) How to switch the security type (Key CD security/ Memory Stick security) Check that the unit is in standby How to operate the ESN (Key CD) security How to cancel the Key CD A [SEC] message appears, then in two seconds it will change to [DISC] Insert your Key CD into the slot How to change the Key CD First, cancel the existing Key CD Refer to "How to cancel the key CD Next, program a new Key CD Refer to "How to program the Key CD What happens if an incorrect CD is inserted After the 5th incorrect attempt, the display reads [HELP] for five seconds Press the [OPEN] or [CD] button to close the front panel Press the [FUNC] button, then button [6], and hold III them for five seconds Press the [FUNC] button How to operate the ESN (Memory Stick) security How to record a security code A [SEC] message appears, in two seconds it will change to [MS] Insert the Memory Stick into the slot A [ - - - -](security code input display) appears Press the [FUNC] button for more than one second Eject the Memory Stick Refer to "Ejecting the Memory Stick" on page How to cancel the Memory Stick security Canceling the security function by entering the security code A security code is entered by pressing the buttons [1] to [4] Canceling the security function using a Memory Stick Press the [DISC] button A [MS] message will appear Insert the Memory Stick and close the front panel The recorded data will be read from the Memory Stick How to change the Memory Stick Cancel the security code that has been recorded with the deck Refer to "How to cancel the Memory Stick security" on page Re-recordthe new Memory Stick and security code that you would like to use Refer to "How to record a security code" on page Canceling ESN security lock out using security code entry Canceling ESN security lock using Memory Stick Insert the Memory Stick that has been recorded, and then close the front panel What happens if a Memory Stick or security code is incorrect ● Note ● How to operate the ACC security How to turn the security indicator on/off [IND. FLASH] or [IND.-----]appears on the display How to read the Electronic Serial Number Turning the power on and off When power is OFF, press the [PWR] button The power will come ON When power is ON, press the [PWR] button for less than two seconds The power will go OFF and the deck will be in Standby Listening to CD The front panel opens Insert a CD into the disc slot, label side up The CD will immediately start playing Listening to MG Memory Stick Insert a MG Memory Stick into the Memory Stick slot Press the [DISC MS] button to switch to the Memory Stick mode MG Memory Stick will start playing Listening to the tuner Press the [FM AM] button This will turn the tuner on Turn the [SEL] button to the left or right to tune to a station Turn to the right: Tunes to higher frequencies Adjusting audio volume Turn the [AUDIO CONTROL] button to the left or right Turn to the right: Increases the volume Turn to the left: Decreases the volume Switching audio control modes VOL (VOLUME) Mode BASS Mode MID (MIDDLE) Mode TREB (TREBLE) Mode BAL (BALANCE) Mode FAD (FADER) Mode NON-F (NON-FADER)Mode SVC (Source Volume Control) Mode Setting examples: Audio mode Default value (Volume level) Enabling the loudness control Making changes with Display Adjustment Mode Press the [DISP] button for less than one second Enters display adjustment mode *: Only when the DSP amp is connected Switching the motion picture Turn the [SEL] button to select the Motion Picture Press the [SEL] button Turn the [SEL] button to select the Motion Picture Type A, B, C and OFF Press the [RTN] button Switching the brightness Turn the [SEL] button to select Bright Turn the [SEL] button to adjust brightness Changing illumination color Turn the [SEL] button to select ILL Turn the [SEL] button to adjust the illumination color Disabling the display You can turn the display on and off in the following way Turn the [SEL] button to select Disp ON/OFF The screen for turning the screen display on and off will appear Turn the [SEL] button to select ON or OFF Importing DISP screens (URL: http://www.e-iserv.jp) Turn the [SEL] button to select Disp Data The Disp Data mode is activated Turn the [SEL] button to select media types ●When using a CD-R: ●When using a Memory Stick: Page Displaying Amplifier Status (E-AMPDISP) Turn the [SEL] button to select E-AMPDISP Turn the [SEL] button to select which amplifier status you wish to display Turn the [SEL] button to change display content Making changes with Function Mode A variety of settings can be changed Press the [FUNC] button for less than one second The function mode is activated *2: Cannot make settings other than for CD or CD changer operation Page Disabling the guide tone feature (for button operation) Turn the [SEL] button to select Guide Tone Press the [FUNC] or [RTN] button to exit function mode Clock display on/off Switches the clock display to ON/OFF Turn the [SEL] button to select Clock The clock display ON/OFF mode is activated Setting the time Turn the [SEL] button to select Clock Adjust Press the [SEL] button to display the item to be selected for adjustment Turn the [SEL] button Switching demonstration screen display Turn the [SEL] button to select the Demo Setting the steering switch function (U.S.A. only) Reading steering switch data Turn the [SEL] button to select Steering SW Select media by turning the [SEL] button Insert the Memory Stick or CD-Rto be used for saving the steering switch data The selected file name is highlighted Page Compatibility with various switches Others Operation assist function Displaying a memo Setting a memo Press the [] button to select the character type Turn the [SEL] button to the left or right to select characters.IV Turn to the right: Advances the character forward in its type Turn to the left: Moves the character backward in its type Press the [SEL] button to select characters Listening to CDs Turn the [SEL] button to the left or right Turn to the right: Advances to the next track Fast Forward/Rewind Fast forward or rewind the song currently being played Press and hold the [] or [] button Press the [5 RPT] button to repeat the track being played To cancel, press the [5 RPT] button again Press the [6 RAND] button to play the tracks in random order To cancel, press the [6 RAND] button again Ejecting the disc Press the [CD ] button The front panel opens and the disc is ejected Remove the disc and press the [CD] or [OPEN] button Creating a title for a CD Press the [FUNC] button for less than one second while in the disc mode Turn the [SEL] button to select Title Turn the [SEL] button to the left or right to select characters Changing a previously set title Press either [SEL] or [ the position in the characters ] button to move the cursor to title for inserting or changing Page Deleting a previously created title Hold the [6] button down for more than two seconds Displaying CD text Press the [DISP] button for more than one second About MP3/WMA ID3/WMA tags Media Format of discs ● Maximum directory layers: ●Number of files/folders possible on a single disc: ●Total number of folders possible on a single disc: ● Maximum folders this deck can recognize: File names Multi-sessions Playing MP3/WMA MP3/WMA playing time display Display order of MP3/WMA file/folder names Listening to MP3/WMA file Skipping to the next or previous folder Press button [1 ] or [2 ] Return to the root directory of the CD Playing the beginning of files (SCAN) Repeating the same file (REPEAT) Press the [5 RPT] button Press the button briefly to repeat the file being played Playing files in random order (RANDOM) Press the [6 RAND] button Displaying title Each time the button is pressed, the following will be displayed in order Folder Name/File Name* ➔ Tag Page Press and hold the [] or []button Page Ejecting the Memory Stick Press the [OPEN] button Lightly press the Memory Stick once Recording on Memory Stick Insert the MG Memory Stick Recording begins When recording a music CD, the CD plays simultaneously Recording stops Selecting tracks to be recorded Turn the [SEL] button to select Memory Stick Turn the [SEL] button to select REC Mode Turn the [SEL] button to select All or 1 Track Setting sound quality Turn the [SEL] button to select REC Quality Turn the [SEL] button to select 66kbps, 105kbps or 132kbps Deleting recorded file Turn the [SEL] button to select Delete Turn the [SEL] button to select the file to be deleted Press the [SEL] button for more than two seconds Formatting MG Memory Stick (quick format) Turn the [SEL] button to select Format Page First, press the [FM AM] button to start tuner operation Tuning to a station ] button: Entering stations into memory automatically (The automatic preset mode: ASM) Press the [SEL] button for more than two second until a VIII beep is heard The automatic preset mode starts These buttons are called preset buttons Manually setting stations into memory Press the [FM AM] button for less than one second to switch between FM and AM Select any button, from [1] to [6], and press it for more than two seconds Preset station scan Press the [SEL] button for less than two seconds To stop the preset scan mode at a desired station, press the [SEL] button again Setting a station name Press the [FUNC] button for less than one second while in the tuner mode Turn the [SEL] button to select Station Name Page Deleting a station name Changing the reception sensitivity for automatic scanning Check that the deck is in standby mode Changing the radio band location FM reception characteristics FM reception differs from AM Fading out Reception area of FM broadcasts Multipath About Sound Adjustment Mode Normal mode Advance mode DSP ○(See page 125) Position selector SRS Circle Surround II (CS II) DSP Parametric equalizer [Parametric equalizer characteristics] Median frequency can be varied Gain can be varied Q (sharpness/band width) can be varied In the deck’s advance mode, 7-bandscan be adjusted with a parametric equalizer Time Alignment Crossover ●The crossover function is a filter that allocates specified frequency bands Multi-harmonizer Non-faderphase Non-Faderoutput E-iSERVsound effect customizations ●Automatic parametric equalizer (Advance Mode Only) ●Time alignment and crossover adjustment URL: http://www.e-iserv.jp Operations during Normal Mode Press the [SOUND] button Turn the [SEL] button to select a setting item DSP Setting Turn the [SEL] button to select DSP Turn the [SEL] button to select the room size Press the [SOUND] or [RTN] button to exit sound adjustment mode Position selector setting (POSITION) Turn the [SEL] button to select POSITION The mode will change to position selector setting mode Turn the [SEL] button to select the setting item When the button is turned, the setting item changes in the following order Turn the [SEL] button to select Non-FPhase Turn the [SEL] button to select NORMAL or IX REVERSE Turn the [SEL] button to select X-Over The mode will change to crossover setting mode Turn the [SEL] button to select the cut-offfrequency When the button is turned, the frequency changes in the following order 63Hz ↔ 80Hz ↔ 100Hz ↔ 125Hz ↔ 160Hz ↔ 200Hz ↔ Multi-harmonizersettings (Harmonizer) Turn the [SEL] button to select Harmonizer Non-FaderOutput Turn the [SEL] button to select Non-FOutput Turn the [SEL] button to select Stereo or Monaural. Press the [SEL] button Operations during Advance Mode The mode will switch to sound adjustment mode (normal mode) Press the [SOUND] button for more than two seconds Setting CSII modes Turn the [SEL] button to select CSII The mode will change to CSII mode Turn the [SEL] button to set CSII modes as follows: In the Hi and Low settings, Loud and Position can not be changed Parametric equalizer adjustment (PEQ) Turn the [SEL] button to select PEQ Press the [SEL] button to select the band to be adjusted Turn the [SEL] button to select the frequency to be adjusted Press the [6] button to select the Q curve pattern Repeat the operations in steps to to change the settings for each band Hold down a button, [1] to [5], for more than two seconds to preset a value Selecting an equalizer mode from memory Press a preset button to select the equalizer mode set in memory called preset buttons Select any button, from [1] to [5], and press it for less than two seconds Measuring/display frequency characteristic Turn the [SEL] button to select the PEQ The mode will be change to parametric equalizer adjustment mode Press the [AUDIO CONTROL] button for less than two seconds After pushing the button, a 10-secondcountdown begins Leave the vehicle during that time of the frequency characteristics will start. [Measuring] will appear on the display while measurement is in progress Page Simplified time alignment settings (Time Alignment) Turn the [SEL] button to select Time Alignment Position selector setting (Position) Turn the [SEL] button to select Position Other time alignment items can be set at this time Selecting the type of vehicle (Car Type) Turn the [SEL] button to select Car Type Page Tweeter settings (Tweeter) Turn the [SEL] button to select Tweeter The mode will change to tweeter setting mode Rear speaker position selection (Rear SP) Turn the [SEL] button to select Rear SP When the button is turned, the frequency changes in the IX following order [] button : The slope becomes more gentle [] button : The slope becomes steeper Page Page Turn the [SEL] button to select Stereo or Monaural Press the [SEL] button. Press the [RTN] button Importing Sound Data Turn the [SEL] button to select Sound Data Turn the [SEL] switch to select media types Insert a CD-Ror a Memory Stick Turn the [SEL] button to select the file Page About the AREA SHOT To use the AREA SHOT function The process is as follows: Map data GPS (Global Positioning System) GPS information may not be available under the following circumstances: ●When radio waves are interrupted by objects on or near the GPS antenna In some instances, wave transmission is interrupted by the U.S Reading the AREA SHOT data Turn the [SEL] button to select AreaShot Turn the [SEL] button to select Disc or Memory Stick Insert the Memory Stick or CD-Rto be used for read the Area Shot data Press the [OPEN] button to close the front panel Turn the [SEL] button to select the saving file The selection file name is highlighted Changing the AREA SHOT mode Press the [MUTE] button for more than one second Using the AREA SHOT mode AREA SHOT Screen Configuration Switching between guidance points Press [] and [] to switch between guidance points Re-scrollingthrough text information Press the [DISP] button Changing AREA SHOT screens Display Arrows Arrows for indicating turn directions are displayed as follows Depending on driving conditions, arrows indicate the following: U-turn Expressway Precautions in use of the remote control Cleaning the remote control Turning the power on/off Press the [PWR] button Adjusting the audio volume Press the [ ] or [ ] button Muting the volume Switching playback modes Press the [MODE] button Press the button to switch modes in the following sequence: How to play the tuner Select the tuner mode first Selecting a station (manually or automatically) Press the [TUNE•SEEK] button Selecting preset stations Press the [PRESET CH] button How to play CDs Press the [TRACK] button ] button: Advances to the next track (Press repeatedly to move to previous tracks.) Skipping to the next or previous disc [] button: Selects the next higher number disc How to play MP3/WMA ] button: Advances to the next track (file) tracks (files).) Skipping to the next or previous folder [] button: Selects the next folder Replacing the battery Use two AAA size batteries Page Listening to a CD Press the [DISC MS] button for less than one second Rewind Page Skipping to the next or previous CD Specifying a CD to play Press the [SEL] button for less than one second Press a button from [1] to [6] About HD Radio Page Press the [SEL] button for more than two seconds until a beep is heard Page Page Switching between displays when receiving HD Radio HD Radio reception settings Turn the [SEL] button to select HD Radio The selected item will be high lighted Displays the reception setting screen Turn the [SEL] button to select AUTO or OFF In the [OFF] setting, reception is always analog About SIRIUS satellite radio Reception of SIRIUS satellite radio is fee based; you have to subscribe to it The receiver will accept up to 24 stations in memory Selecting the radio mode Press the [FM AM] button for more than one second Selecting a channel Turn the [SEL] button to the left or right to tune to a channel Category selection The channel can be selected from among categories such as POP and ROCK Consult the SIRIUS website for details of categories Press the [] or [] button for more than one second Categories will switch in order shown below each time button is pressed Press the buttons [1], [2] and [3] to select the channel number to be input [1]button. . . . . Hundreds [2]button. . . . . Tens [3]button. . . . . Units Each time the buttons are pressed, the numerals change in the following order Manually setting channels into memory Preset channel scan The receiver will stay tuned to the desired channel Switching displays when using the SIRIUS satellite radio channel name ➔ category name ➔ title ➔ artist ➔ SIRIUS unit ID Connecting portable audio players to the AUX jack Turn on the portable audio player and start its play function Switch to AUX mode by pressing the [DISC] button for more than one second Changing auxiliary input sensitivity Turn the [SEL] button to select AUX Sensitivity Turn the [SEL] button to select the sensitivity mode User Registration Key display Page Displayed information (for troubleshooting) Page Page Page <GENERAL <FM TUNER <AM TUNER <CD SECTION <MEMORY STICK SECTION <AUDIO AMPLIFIER Loudness Components Installation angle Mounting the main unit Mount the stud bolt to the main unit Insert the main unit into the mounting sleeve until it locks in place Fasten the rear of the main unit using either method [A] or [B] Select method [A] or [B] to suit the interior configuration of the vehicle Install the bezel on the main unit. [A] Page Names of lead wires and destinations (refer to Page 204) ● Caution ● Page System 1) CD8445 Receiver, used alone Caution 2) CD8445 + GPS105 + VRM803 3) CD8445 + CH3083 + CH3083 + VRM803 + Power Amplifier Note 4) CD8445 + HDR105 + CH3083 + VRM803 + Power Amplifer 5) CD8445 + CH3083 + 21010 + VRM803 + Power Amplifier Page Page Page CUSTOMER NOTICE Serial No www.eclipse-web.com