Fan Button | The Fan button is used to change the fan speed between High Medium, | ||
Low and Auto while in Cooling and Fan Only modes. | |||
| |||
| Press the Fan button to select the fan speed. The LED indicator light next | ||
| to the High, Medium, or Low will light up. The Automatic Fan speed | ||
| setting does not have a light. | ||
|
|
| |
Timer Button | The timer can be used to either turn the unit on or off after a number of | ||
| elapsed hours. The timer is adjustable between | ||
| increments and from | ||
How to set the unit to automatically turn on:
1)Press the Timer button while the unit is powered off. The Timer On indicator LED will light up.
2)Use the Up and Down buttons to set the time (displayed in hours). The unit will count down the time remaining. After the selected time passes, the unit will automatically turn on.
|
|
|
| How to set the unit to automatically turn off: |
|
|
|
|
|
|
| 1) Press the Timer button while the unit is powered on. The Timer Off |
|
|
|
|
|
|
| indicator LED will light up. |
|
|
|
|
| NOTE: To cancel the |
|
|
| ||
|
| 2) Use the Up and Down buttons to set the time (displayed in hours). The |
|
| |||
|
| timer, press the Power |
|
| |||
|
| unit will automatically count down and turn off after the selected time |
|
|
| ||
|
| button or set the timer to |
|
|
| ||
|
| elapses. |
|
|
| ||
| 0.0. | Note: If the unit displays an E1 or E2 error code, the timer is cancelled. |
|
|
| ||
|
|
|
|
|
|
| |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| |
|
| LED Display | The LED Display will show the set temperature by default. It will show the |
|
| ||
|
|
|
| set temperature while in Dehumidify and Fan Only modes. You can |
|
|
|
|
|
|
| switch between Fahrenheit and Celsius by holding both the Up and Down |
|
| |
|
|
|
| Buttons simultaneously for 5 seconds. If you enabled the Timer, the LCD |
|
| |
|
|
|
| Display will show the hour(s) set. |
|
|
|
|
|
|
| Error Codes |
|
|
|
|
|
|
| The display may show the following error codes: |
|
|
|
|
|
|
| E1 – Room temperature sensor error. |
|
|
|
|
|
|
| E2 – Evaporator temperature sensor error. |
|
|
|
|
|
|
| E4 – Display panel communication error. |
|
|
|
|
|
|
| If the unit displays the error codes E1, E2, or E4, power the unit off, and |
|
| |
|
|
|
| then unplug the unit for 15 minutes. Plug in and power on. If the issue |
|
|
|
|
|
|
| persists, please contact customer service. |
|
|
|
|
|
|
| P1 – Bottom reservoir is full. |
|
|
|
|
|
|
| If the unit displays a P1 error code, drain the unit by following the |
|
|
|
|
|
|
| “Draining the Unit” section. |
|
|
|
|
|
|
|
|
|
| |
| Sleep Button | The Sleep Button is used to enable the Sleep mode. During the Sleep |
|
|
| ||
|
|
|
| mode, the set temperature will increase by 2 degrees after 30 minutes, |
|
|
|
|
|
|
| then it will increase by another 2 degrees after an additional 30 minutes |
|
| |
|
|
|
| and maintain this temperature for 7 hours before it returns to the original |
|
| |
|
|
|
| temperature and ends the Sleep mode. The Sleep mode is not available |
|
| |
|
|
|
| in Dehumidify and Fan Only modes. |
|
|
|
|
|
|
|
|
|
|
|
EdgeStar Portable Air Conditioner | 12 |
|
| ||||
