![](/images/new-backgrounds/1022232/2223219x1.webp)
®
PROFESSIONAL AUDIO & SOUND
DIGITAL MUSIC AMPLIFIERS
DIGITAL
MUSIC SERIES![](/images/new-backgrounds/1022232/2223219xi12.webp)
TM
INSTALLATION AND WIRING
INPUT 1 SETTING AS A MICROPHONE INPUT
MICROPHONE TYPE
The Microphone Input accepts Low Impedance
CAUTION: TO PREVENT POSSIBLE DAMAGE TO SPEAKERS OR THE AMPLIFIER ALL INPUT CONNECTIONS MUST BE MADE WITH THE AMPLIFIER POWER OFF.
PASO MICROPHONES
All PASO low impedance Microphones have a balanced output for best performance. Connect the RED lead to terminal HOT, the WHITE lead to terminal COM and the SHIELD to terminal G.
THREE LEADS BALANCED MICROPHONE WIRING
WIRING
VOX - MUTE JUMPERS SETTING | ||||
|
|
| SW215 | VOX 1 BUSS |
|
|
|
| |
| V1 |
| OFF | ACTIVATED |
|
| JUMPER |
| |
|
|
|
| |
VOX SEND | V2 |
|
| X |
|
|
| ||
|
|
| VOX 2 BUSS OFF | |
|
|
|
| |
|
|
| JUMPER | = JUMPER |
MIC IN |
| AUDIO OUT |
| |
| INPUT 1 |
|
|
|
Input 1 - V1 - 01 |
|
| SW220 |
|
|
|
|
| |
|
| M1 | OFF JUMPER | MUTE 1 BUSS OFF |
|
| X | ||
MUTE RECEIVE |
|
| ||
|
|
| ||
|
| M2 | X |
|
|
|
| MUTE 2 BUSS OFF | |
|
|
|
|
INPUT 1 - Default Jumper Settings
The Diagram at Left shows the
Default Settings for INPUT 1.
VOX 1 is SWITCHED ON
VOX 2 is SWITCHED OFF
MUTE 1 is SWITCHED OFF
MUTE 2 is SWITCHED OFF
When the INPUT 1 (MIC 1) is activated the VOX 1 BUSS is ON and it will MUTE any Input with the MUTE 1 Setting SWITCHED ON.
250ohm 1.5mV
BALANCED
| INPUT 1 (MIC) |
| INPUT 2 (MIC) |
| INPUT 3 | (MIC) | |
| G COM HOT |
| G COM HOT |
| G COM | HOT |
|
|
|
|
|
|
|
|
|
MICROPHONE INPUT
Attach the microphone leads to the ter- minal strip as per diagrams at left.
DO NOT GROUND THE MICROPHONE CABLE SHIELD TO THE CHASSIS OF THE AMPLIFIER
BALANCED MICROPHONE
IMPORTANT NOTE: The use of an unbalanced Microphone (two leads) is not recommended. For best results in a PA Application always use a
Unidirectional Dynamic, Low Impedance, Balanced Microphone
The microphone leads color refers to Paso Microphones only. |
| ||
When using other brand refer to instructions packed with that | NOTE: To change the | ||
unit. | SHIELD | ||
INPUT Default Settings | |||
|
| ||
MIC | WHITE | refer to the appropriate | |
Lo Z | section in this Manual | ||
RED |
| ||
| 3120 Micbal 01 |
Fig. 10 - Balanced Microphone Input 1 Wiring
TWO LEADS UNBALANCED MICROPHONE WIRING
(three leads).
UNBALANCED MICROPHONE
Attach the Microphone leads to the ter- minal strip as per diagram in Fig 8A. The cable length should not exceed: 15 Ft. (4.5 m).
CABLE
VOX - MUTE JUMPERS SETTING
| SW215 | VOX 1 BUSS |
V1 | OFF | ACTIVATED |
JUMPER |
| |
|
| |
VOX SEND |
| X |
V2 |
| |
| VOX 2 BUSS OFF | |
|
| |
| JUMPER = JUMPER |
INPUT 1 - Default Jumper Settings
The Diagram at Left shows the Default Settings for INPUT 1.
VOX 1 is SWITCHED ON VOX 2 is SWITCHED OFF MUTE 1 is SWITCHED OFF MUTE 2 is SWITCHED OFF
When the INPUT 1 (MIC 1) is activated the VOX 1 BUSS is ON
CABLE LENGTH - If the distance between the Microphone and the Amplifier Input is greater than 15 ft (4.5
m)a Balanced Microphone must be used. Use a two conductor shielded wire and connect Microphone to Amplifier as per Diagram in Fig. 10.
MICROPHONE CABLE ROUTING - The
MIC IN | AUDIO OUT |
INPUT 1
Input 1 - V1 - 01
SW220
OFF JUMPER
MUTE RECEIVE | M1 | X |
| ||
| M2 | X |
|
|
MUTE 1 BUSS OFF
MUTE 2 BUSS OFF
and it will MUTE any Input with the MUTE 1 Setting SWITCHED ON.
250ohm 1.5mV
BALANCED
|
| INPUT 1 (MIC) |
| INPUT 2 (MIC) |
| INPUT 3 | (MIC) | |||||||||
|
| G COM HOT |
| G COM HOT |
| G COM |
| HOT |
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Microphone Cable should be carefully routed. Improper Cable routing will cause spurious oscillations, regenerative noises, hum, etc. that may permanently damage the Amplifier.
z | Do not route cable next to power |
| lines. |
z | Do not route cable near or over |
| Fluorescent Fixtures. |
| SHIELD | NOTE: To change the |
| INPUT Default Settings | |
|
| |
MIC |
| refer to the appropriate |
Lo Z |
| section in this Manual |
| HOT LEAD | |
|
| |
|
| 3120 Micunbal 01 |
Fig. 10A - Unbalanced Microphone Input 1 Wiring
z Do not route cable next to |
Speaker Wires. |
z Do not install cable inside Power |
Line Conduits. |
z Avoid the use of staples that may |
penetrate the cable. |
PAGE 10 | SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE | DMS3040/3080/3120 |