A.1 GENERAL INFORMATION

A.1.1 FOREWORD

The purpose of this manual is to provide the necessary information for the correct installation, operation, use and maintenance of the appliance.

Consequently, the manual and all the technical documentation enclosed with the appliance must be kept with the appliance at all times so that they can be consulted by the technician or end user. It is important to inform the appliance user about regulations concerning safety during and after installation.

Read the instructions in the manual carefully before carrying out any operation whatsoever on the appliance, as they give important information about the standards and rules governing its installation and safe use. Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death. Failure to observe the instructions in this manual when carrying out any operations on the appliance will relieve the manufacturer of all liability. Also, the manufacturer declines any responsibility in the event of problems caused by the use of non-original spare parts.

No part of this of this manual may be reproduced.

A.1.2 INTENDEDUSEANDLIMITATIONS

This appliance has been designed for the refrigeration and preservation of foodstuffs. Any other use is to be considered improper.

ATTENTION: these appliances are not suitable for installation outdoors and/or in environments subject to natural elements (rain, direct sunlight, etc.).

The manufacturer declines all liability for any improper use of the product.

A.1.3TESTING

Our appliances have been designed and optimised with laboratory testing to give high performance and efficiency. The product has gone through 100% testing and is ready for use. The certificates guaranteeing that the tests (visual inspection - electrical test - functional test) have been passed are included with the appliance and are included in specific enclosures (section D.6).

A.1.4GENERALSAFETYRULES

The appliance is manufactured in compliance with following

directives:

ANSI / NSF 7

- Hygiene:

- Safety:

UL 471

-CAN / CSA C22.2 No.120 - M91

For models:

RI93RE1FEU,RI17RE1FU.

serial number located underneath the logo.

A.1.7PHYSICALSAFETYFEATURES,HAZARDS The appliance has no sharp or projecting parts.

DANGER! DO NOT REMOVE. There are guards on the units to prevent access to components which require air movement.

B.1 INSTALLATION

WEAR PROTECTIVE GLOVES WHEN UNPACKING AND INSTALLING THE APPLIANCE.

Read these instructions carefully before attempting installation. Installation and initial

startup should be performed by a qualified installer. Unless the installation instructions for this product are followed by a qualified service technician (a person experienced in and knowledgable with the installation of commercial equipment) then the terms and conditions on the Manufacturer's Warranty will be rendered void and no warranty of any kind shall apply.

IFINDOUBTPLEASECONTACTLOCALSERVICE AGENCY.

B1.1IMMEDIATEINSPECTFORSHIPPINGDAMAGE

The container should be examined for damage before and during unloading. The freight carrier has assumed responsibility for its safe transit and delivery. If damaged equipment is received, either apparent or concealed, a claim must be made with the delivering carrier. Apparent damage or loss must be noted on the freight bill at the time of delivery. The freight bill must then be signed by the carrier representative (Driver). If the bill is not signed, the carrier may refuse the claim. The supplier can supply the necessary forms. A request for inspection must be made to the carrier within 15 days if there is concealed damage or loss that is not apparent until after the equipment is uncrated. The carrier should arrange an inspection. Be certain to hold all contents plus all packing material. Under no circumstances should a damaged appliance be returned to the manufacturer without prior notice and written authorization.

CAUTION:

the operations described below should be carried out in com- pliance with current safety regulations, with reference both to the equipment used and the operating procedures.

IMPORTANT: before moving the appliance, make sure that the load-bearing capacity of the lifting equipment to be used is suitable for the weight of the appliance.

A.1.5CUSTOMER’SRESPONSIBILITIES

A fused disconnect switch or a main circuit breaker (customer furnished) MUST be installed in the electric supply line for the appliance. It is recommended that this switch/circuit breaker have lockout/tagout capability. Before making any electrical connections to this appliance, check that the power supply is adequate for the voltage, amperage, and phase requirements on the rating plate. The customer also must provide a grounded electrical line cord of suitable capacity for the input specified on the data plate.

A.1.6 DATA PLATE POSITION

The data plate with all the appliance specifications is located on the refrigeration unit compartment at the top right hand side. There is also a plate bearing the appliance’s PNC code and

B.1.2REMOVINGTHEPACKAGING

B.1.2.1 Removing the packaging and handling

Cut the straps and remove the protective film, taking care not to scratch the sheet metal if scissors or blades are used. Remove the top (in cardboard), the polystyrene corners and the vertical protection pieces. For appliances with stainless-steel cabinets, carefully remove the protective film without tearing it, to avoid leaving glue stuck to the surface.

Should this happen, remove the traces of glue with a non- corrosive solvent, rinsing it off and drying carefully. It is advisable to go over all the s/steel surfaces with a rag soaked in vaseline oil, in order to form a protective film. Use a transpallet or fork- lift truck to lift appliances. Inserting the forks under the pallet, lift the appliance and carry it to the place of installation, making sure

10 that the load is balanced.

Page 9 Page 11
Page 10
Image 10
Electrolux 727027 Foreword, Intendeduseandlimitations, 3TESTING, 4GENERALSAFETYRULES, Ansi / NSF, RI93RE1FEU,RI17RE1FU
Page 9 Page 11

727027, RI17RE1FU, 727028, RI93RE1FEU specifications

The Electrolux RI93RE1FEU and RI17RE1FU are innovative refrigeration units designed to deliver optimal cooling performance and energy efficiency for modern households. These models boast a blend of advanced technologies and user-friendly features that cater to various storage needs while ensuring freshness and convenience.

One of the most notable features of the RI93RE1FEU is its SpaceMax technology, which maximizes internal storage capacity without altering the external dimensions of the appliance. This allows users to store more food items efficiently, making it ideal for families or individuals who require ample refrigeration space. The RI17RE1FU model complements this with a sleek design that fits seamlessly into contemporary kitchens while providing substantial storage options.

Energy efficiency is a core characteristic of both models. With high energy ratings, they help consumers reduce their electricity bills while contributing to a more sustainable environment. The A++ energy rating signifies their compliance with the latest energy standards, ensuring that they consume less power without compromising performance.

In terms of cooling technologies, both models feature MultiFlow technology, which ensures even distribution of cold air throughout the refrigeration compartment. This not only maintains a consistent temperature but also helps to keep food fresher for longer by minimizing temperature fluctuations. Additionally, the NoFrost feature found in the RI93RE1FEU eliminates the need for manual defrosting, saving users time and effort. The frost-free system ensures that ice does not build up, providing hassle-free maintenance.

The Electrolux RI93RE1FEU and RI17RE1FU also boast adjustable shelves and door bins, allowing for customizable storage solutions tailored to individual needs. This flexibility is crucial for users looking to maximize space for different types of groceries, from tall bottles to smaller containers.

Furthermore, both models are equipped with sophisticated control systems that enable users to monitor and adjust temperatures with ease. Intuitive displays and controls provide quick access to settings, ensuring that food items remain at the ideal temperature.

These Electrolux models combine practicality with style, offering a blend of performance, energy efficiency, and user-friendly features. With their advanced technologies, consumers can enjoy peace of mind knowing that their food will stay fresh and accessible whenever needed.
Top Page Image Contents