Electrolux RI93RE1FEU, 727027 1HACCPCONNECTIONS, Report PRINT-OUTS, 1QUICKTROUBLESHOOTINGGUIDE

D.3 HACCP CONNECTIONS (ACCESSORIES)

D.3.1HACCPCONNECTIONS

Refer to the handbook enclosed with the kit for instructions on installing the accessories.

Basic system connection

The printer can provide a print-out of data collected by the probe connected to the electronic board. To do this, connect the se- rial cable (shielded) to the printer and the appliance itself. The serial cable connector is located behind the control panel.

Set the print interval (see TPRN parameter); and specify the type of report by setting the “PRND” parameter.

REPORT PRINT-OUTS

Report print-outs are produced automatically when the appli- ance is switched on.

The print-out contains data measured by electronic the board and indicates:

- the date and time of start-up, repeated every 20 lines of tem- perature;

-the chamber temperature at pre-set intervals (TPRN user parameter);

-the description of the type of alarm generated complete with the exact time of the start and end of the alarm;

-time of the start and end of defrosting.

D.4 TROUBLESHOOTING

D.4.1QUICKTROUBLESHOOTINGGUIDE

In some cases faults can be remedied easily and quickly. Below there is a list of possible faults and remedies:

A. The appliance doesn’t switch on:

-check that the main circuit breaker is powered.

B.The appliance does not reach the set internal temperature:

-check that the condenser is clean;

-check that the cycles have been set properly;

-check that the product has been loaded properly into the chamber;

C.The appliance is excessively noisy:

-check that the appliance is properly levelled. If it is unbalanced this could cause vibrations.

-check that the cabinet is not touching other units, as this may cause resonant vibrations.

If the defect persists after having carried out the above checks, contact the service center, remembering to give the following details:

•the nature of the fault;

•the appliance’s PNC (production number code);

•the Ser. No. (appliance serial number).

Note: the data plate with all the appliance specifications is located on the refrigeration unit compartment at the top right hand side. There is also a plate bearing the appliance’s PNC code and serial number located underneath the logo. These are essential for identifying the type of appliance and date of manufacture.

PNC 726377

Ser.No. 44600010

Example: PNC 726377 00 - Ser.No. 44600010

726377 00: Prostore Smart

44600010: manufactured in 2004, week 46, 10th item.

D.5 WASTE DISPOSAL AND DEMOLITION

D.5.1WASTESTORAGE

At the end of the appliance’s working life, make sure it is dis- posed of properly. Make sure you remove the doors before scrapping the appliance.

Special waste materials can be stored temporarily while await- ing processing for disposal and/or permanent disposal. In any event, the binding environmental protection laws in the country of use must be observed.

D.5.2 PROCEDUREFORPRELIMINARYDISMANTLING OFTHEAPPLIANCE

All countries have different legislation; provisions laid down by the laws and the authorized bodies of the countries where demolition takes place are therefore to be observed.

In general terms, the refrigerator must be taken to a special- ized collection/demolition center.

Dismantle the refrigerator and group the components together according to their chemical characteristics (plastic parts are marked with letters identifying the material). Bear in mind that the compressor contains lubricant oil and coolant, which can be recycled, and that the refrigerator components are classed as special waste that cannot be disposed of as urban waste. Make the appliance unusable by cutting off the power supply cable and removing the door and or locking mechanisms in order to avoid the risk of anyone becoming trapped inside.

DISMANTLING OPERATIONS MUST BE CARRIED OUT BY QUALIFIED PERSONNEL.

D.6 ENCLOSED DOCUMENTS

•Set of test and inspection documents

•Wiring diagram

•Installation diagram

19