Electrolux EKM 90310 X, EKM 90410 X Electrical Connection, Replacing of the Cable, GAS Adjustment

ELECTRICAL CONNECTION

This appliance must be installed by a qualified person in accordance with the latest IEE Regulations and in compliance with the manufacturer’s instructions.

Check that the voltage is the same as that stated on the rating plate. The rating plate is located on the back cover.

WARNING! THIS APPLIANCE MUST BE EARTHED

If an fixed appliance is not equipped with supply cable and plug, the power supply must be fitted with a disconnect switch in which the distance between contacts permits total disconnection in accordance with overvoltage category III, as required by installation regulations. We recommend that the cooker circuit is rated to 13 amps.

Cable type HO5 RRF 3 X 1.5 mm2

Connecting the mains cable

Open the mains terminal block cover as shown, unscrew screw “A” the cable clamp, and loosen the screws in the mains terminal block “L N E” which secure the three

wires of the mains cable. Fit the cable and refit screw “A”, the cable clamp.

Allow sufficient cable length for the cooker to be pulled out for cleaning, but do not let it hang lower than 50mm (2”) from the floor. The cable can be looped if necessary, but make sure that it is not kinked or trapped when the cooker is in position.

IMPORTANT

The wires in the mains cable are coloured as follows:

GREEN AND YELLOW	........EARTH
BLUE	NEUTRAL
BROWN	LIVE

REPLACING OF THE CABLE

If the cable becomes damaged or worn, replace it, observing the following instructions:

-open the box of the supply board as shown in the diagram below;

-unscrew screw “A” that secures the cable;

-replace the cable with one of the same length and which corresponds to the features described in the table; switch the appliance off, and shut the gas tap;

- connect the ‘green-yellow” earth wire to the terminal “	“, leaving
it approximately 10 mm longer than the live wire;

-connect the “blue” neutral wire to the terminal marked “N”;

-connect the live wire to the terminal marked “L”.

GAS ADJUSTMENT

Always isolate the cooker from the electricity supply, shut off the gas supply temporarily and proceed as follows.

-change the injectors,

-adjust the minimum flow of the burners.

REPLACEMENT OF COOKTOP INJECTORS

To change the cooktop injectors, proceed as follows: remove the grids, remove burners and flame-spreaders (see fig.A), change the injector (see fig.B) and replace it with another one suitable for the new type of gas (see table D). Re-assemble everything in reverse order, ensuring you position the flame-spreader correctly.

A B

GB

TAB. D

Values referred to Hs - 15°C - 1013,25mbar

Cat. II 2H3+

TABELLA GENERALE INIETTORI

Kind of gas	mbar	Nozzle	Burners		Power KW		Consum		N°
		N°			max.	min.	max.	min.	By pass
		115	Rapide	3,00		0,75	286 l/h	72 l/h	reg.
NATURAL	20	97	Semi rapide	1,75		0,48	167 l/h	46 l/h	reg.
G 20		72	Auxiliary	1,00		0,33	95 l/h	31 l/h	reg.
		128	Triple crown	3,30		1,30	315 l/h	124 l/h	reg.
BUTANE	28-30	85	Rapide	3,00		0,75	219 g/h	55 g/h	42
G 30		65	Semi rapide	1,75		0,48	128 g/h	35 g/h	31
		50	Auxiliary	1,00		0,33	73 g/h	24 g/h	27
PROPANE	37	93	Triple crown	3,30		1,30	241 g/h	95 g/h	60
G 31

MINIMUM FLOW ADJUSTMENT FOR COOKTOP TAPS

To adjust the minimum, proceed as follows: switch the burner on, and turn the knob towards the minimum flow position . Remove the knob from the tap, introduce a small screwdriver in to the tap rod (fig. 11). Attention: in taps with security valve, the minimum adjustment screw “Z” is placed outside the tap rod (fig. 12).

	Z
Fig. 11	Fig. 12

Loosen the adjustment screw in order to increase the flow or tighten it to decrease the flow.

The proper adjustment is obtained when the flame is approximately 3 or 4 mm in length.

For butane/propane gas, the adjustment screw must be fully screwed down.

Make sure that the flame does not go out when passing quickly from the max. flow to the minimum flow .

Assemble the knob again.

APPLIANCE MAINTENANCE

WARNINGS

Isolate the cooker from the electricity supply before attempting to replace the oven lamp.

The oven lamp is of a special type designed to withstand high temperatures. To replace it, proceed as follows: remove the protective glass (A) and replace the burnt-out bulb with one of the same type. Re-fit the protective glass.

E 14

25 W - 230 V~ T300°C

A

DISMANTLING THE COOKTOP

If it becomes necessary to repair or replace internal components, proceed as follows: remove the glass lid from its position by sliding off upwards.

Remove the grids, the burners and flame-spreaders (see fig. 13), unscrew the visible screws “V” located on the cooktop (see fig. 14). Dismantle the cooktop by unscrewing the 4 rear screws “A” (see fig. 15 ).

7