Electrolux ELECTRIC WHEELED Rotary Lawnmower manual Wheel Assembly, Lower Handles, Upper Handles

Safety Precautions

12.Keep hands and feet away from the cutting means at all times and especially when switching on the motor.

13.Do not tilt lawnmower when the motor is running, except when starting and stopping. In this case, do not tilt more than absolutely necessary and lift only the part which is away from the operator. Always ensure that both hands are in the operating position before returning the appliance to the ground.

14.Do not put hands near the grass discharge chute.

15.Never pick up or carry a mower when it is operating or still connected to the mains supply.

16.Remove the plug from the mains :

-before leaving the mower unattended for any period;

-before clearing a blockage;

-before checking, cleaning or working on the appliance;

-if you hit an object. Do not use your lawnmower

until you are sure that the entire lawnmower is in a safe operating condition;

-if the lawnmower starts to vibrate abnormally. Check

immediately. Excessive vibration can cause injury.

Maintenance and storage

1.Keep all nuts, bolts and screws tight to be sure the lawnmower is in safe working condition.

2.Check the grassbox/grassbag frequently for wear or deterioration.

3.Replace worn or damaged parts for safety.

4.Only use the replacement blade, blade bolt, spacer and impeller specified for this product.

5.Be careful during adjustment of the lawnmower to prevent entrapment of the fingers between moving blades and fixed parts of the machine.

Wheel Assembly

1.Select one of the holes in the mounting plate and

note it as the other wheels will need to be adjusted to the same position. (A1)

2.Locate the fixing bolt through hole in the hub cap, wheel and selected hole in mounting plate.

3.Turn the wheel hub in a clockwise direction until the wheel assembly is securely located to the deck. (A2)

Lower Handles

Lower Handles - 37cm (B1, B2)

1.Locate 2 screws into the holes in the handles.

2.Using a pozidrive screwdriver, secure the screws

into the lower handles, ensuring the point of the screw stays inside the handle. (B1)

3.Insert lower handles, with screws attached, into

the deck and fully tighten screws. (B2)

Note: The screw will form its own thread Lower Handles - 42cm (C1, C2)

1. If your product has Cutting Height with levers,

ensure the lever is at the Highest Cut Height before following steps 2 & 3.

2.Insert each side of the lower handles into deck as shown in Fig C1.

3.Push each side of the handle firmly down until it is located securely into the deck (C2).

4.Insert screw through the washer and into holes

using a pozidrive screwdriver and tighten fully into deck as shown in Fig C2.

Upper Handles

1.The upper handle should be fixed to the lower

handle using whichever type of kit is provided as shown in Figs D1, D2 and D3.

2.Fit the cables to the handles with the cable ties provided, making sure the cables are not trapped between the upper and lower handles.

Grassbox Assembly

Grassbox Assembly - 37cm.

1.Insert the grassbox handle into the top of one of

the grassbox halves. Press firmly down and forward until the handle clicks into position (E)

2.Turn the grassbox half over and insert screw into hole (as illustrated in fig E) and tighten fully.

3.Locate grassbox upper into grassbox lower. (F) Align clips, ensure all clips are correctly located.

4.Clip the two halves together.

5.Ensure all clips are securely connected.

Grassbox Assembly - 42cm

1.Insert the grassbox handle into the top of one of

the grassbox halves. Press firmly down and forward until the handle clicks into position (E)

2.Turn the grassbox half over and insert screw into hole (as illustrated in fig E) and tighten fully.

3.Position the two grassbox halves together and press each location point (G1-A)into position without fully

connecting the clips. When the location points are matched correctly firmly press the grassbox together

until all clips are securely connected.(G1-B, G2) 37cm, 42cm

1.To attach the grassbox to your lawnmower, lift the safety flap (H) and make sure the discharge chute is clean and free from debris.

2.Locate fully assembled grassbox onto 2 location points at the rear of the deck. (H)

3.Locate safety flap onto the top of the grassbox. Ensure the grassbox is securely located.

•Removal is the reverse procedure.

•Please Note Ensure no gap remains between the safety flap and the grassbox/bag

•Where grass collection is not required you can use the lawnmower without the grassbox/bag. Ensure the safety flap is fully closed

Cable Restraint

Cable Restraint (J1 ,J2, J3)

1.Attach cable restraint above switchbox (J1).

2.Form loop in mains cable and push the loop through (J2).

3.To secure, position loop over the hook and pull cable back through the slot. (J3)

Cable Restraint (K1, K2, K3)

1.Connect female extension cable connector to the back of the switchbox. (K1)

2.Form loop in mains cable and push the loop through the slot. (K2)

3.To secure, position loop over the hook and pull the cable back through the slot.(K3)

ENGLISH - 2