Installation instructions
Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person.
Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person.
Remove all packaging before positioning the machine.
If possible, position the machine next to a water tap and a drain.
Water supply connections
This dishwasher may be fed with either hot (max. 60°) or cold water. Nevertheless we advise you a cold water supply.
A hot water supply is not always efficient with very soiled crockery as it shortens the washing programmes a lot. The water pressure must be within the limits given in the technical specifications.
Your local Water Authority will advise you on the average mains pressure in your area.
The dishwasher features fill and drain hoses which can be
turned either to the left or the right to suit the installation. The locknut must be correctly fitted to avoid water leaks.
Do not use, for connection, old hoses which have been used in another appliance.
Avoid bends or kinks in the hose which could prevent or slow down the water supply.
If the machine is connected to new pipes or pipes which have not been used for a long time, you should run the water for a few minutes before connecting the inlet hose. This will prevent deposits of sand or rust clogging the inlet hose filter.
For making the connection itself, the coupling nut fitted to the machine’s supply hose is designed to screw onto either a 3/4 inch gas thread spout, or to a purpose made
tap such as the Press-block.
The waste connection must be at a height of between 30 cm (minimum) and 100 cm (maximum) from the bottom of the dishwasher.
The drain hose can face either to the right or left of the dishwasher
Ensure the hose is not bent or squashed as this could prevent or slow down the discharge of water.
If you use a drain hose extension it must be no longer than 2 metres and its internal diameter must be no smaller than the diameter of the hose provided.
Likewise the internal diameter of the couplings used for connections to the waste outlet must be no smaller than the diameter of the hose provided.
Ø 18 | Ø 21 |
|
|
|
| cm | min 30 cm max 100 cm |
+ 2 m max | max 100 | ||
|
| ||
CS10 |
|
|
|
The sink plug must not be in place when the machine is draining as this could cause the water to siphon back into the machine.
Attention!
Our appliances are supplied with a security device to protect against the return of dirty water back into the machine.
If the spigot of your sink has a "no return valve" incorporated this can prevent the correct draining of your dishwasher.
We advise you therefore to remove it.
Be sure to incorporate the filter (A) supplied with the machine onto the joint.
A |
CA02 |
Electrical connection
Before plugging the appliance into the wall socket, make sure that:
1.The mains voltage corresponds to the voltage given in the "Technical specifications".
2.The meter, fuses, mains power supply and wall socket can all take the maximum load required.
Make sure that the socket and plug are compatible without having to use any type of adaptor. If necessary, have the domestic wiring system socket replaced.
Water outlet hose connection
The end of the drain hose can be connected in the following ways:
1.To the sink outlet spigot, securing it if necessary with a clip.
2.Hooked over the edge of the sink using the special curved plastic guide provided.
3.To a stand pipe provided with
|
| 1 | 2 | 3 |
| 21 |
|
| 4 cm |
Ø | 18 |
| min | |
Ø |
| |||
|
|
| ||
|
|
|
| |
|
|
| max 100 cm | min 30 cm max 100 cm |
CS09 |
|
|
|
|
Safety standards require the appliance to be earthed.
The manufacture accepts no liability for failure to observe the above safety precautions.
28
