Filling with salt
Only use salt specifically designed for use in dishwashers.
All other types of salt not specifically designed for use in
a dishwasher, especially table salt, will damage the water softener.
Only fill with salt just before starting one of the complete washing programmes.
This will prevent any grains of salt or salty water, which may have been spilled, remaining on the bottom of the machine for any period of time, which may cause corrosion.
To fill:
1.To fill with salt, unscrew the cap of the salt container.
2.Pour 1 litre of water inside the container ( | this is necessary |
only before filling with salt for the first time | ). |
Rinse aid
Rinse aid is automatically added during the last rinse, ensuring thorough rinsing, and spot and streak free drying. The dispenser, which is positioned inside the door, holds about 110 ml of rinse aid, which is sufficient for 16 - 40 dishwashing programmes, depending upon the dosage setting.
Filling with rinse aid
1.Open the container by turning the lid (A) anticlockwise.
2.Add the rinse aid until the container is completely full. The indicator (B) will be completely dark.
3.Top up the rinse aid when the rinse aid indicator light on the control panel illuminates.
3.Using the funnel provided, pour in the salt until the container is full.
Do not worry if water over flows from the unit when filling with salt, this is quite normal.
4.Replace the cap making sure that there is no trace of salt on the screw thread or on the gasket.
SALET |
SAL |
SALZ |
SEL |
SR06 |
A |
BR01 |
B |
|
|
|
|
|
| x | 6 | 5 | 4 | 3 |
|
| ||||
m | a |
|
|
| 2 |
|
|
|
| 1 | |
|
|
|
|
| |
BR03 |
|
|
|
|
|
If rinse aid refilling is necessary, the rinse aid indicator light will illuminate only in setting mode and at the end of
5.Screw on the cap tightly.
The salt container will require topping up periodically.
You are reminded of this by the salt indicator light on the control panel which comes on when the salt has finished.
The salt indicator light on the control panel can remain illuminated for
From level 2 upwards, if salt refilling is necessary, the salt indicator light will illuminate only in setting mode and at the end of the washing programme. During the run of the programme it will remain off.
the washing programme.
During the run of the programme it will remain off.
Ensure that the lid is closed after every refill.
Do not put liquid detergent in the rinse aid compartment. Clean up any rinse aid spilt during filling with an absorbent cloth to avoid excess foaming during the next wash.
It is possible to deactivate the rinse aid indicator light (see the following instructions), By default the rinse aid indicator light is active.
To deactivate the rinse aid indicator light be sure that the dishwasher is off and then proceed as follows:
1. | Press | Intensive 70° 80’ and Normal 65° | programme push | ||
| buttons simultaneously. |
|
| ||
2. | While keeping the programme push buttons | Intensive 70° | |||
| 80’and | Normal 65° | pressed switch on the dishwasher by | ||
| pressing the | On/Off | push button. |
| |
| The | On/Off indicator light comes on. |
| ||
| At the same time, the indicator lights of the | Intensive 70° | |||
| 80’and | Normal 65° | push buttons start flashing. |
|
SO406
3. Press the | Normal 65° push button, the correspondent |
| |
indicator light keeps flashing while the indicator light of the |
| ||
Intensive 70° 80’ push button turns off. |
|
| |
At the same time the indicator light " | end of programme | " | |
starts to flash. |
|
|
20