Snapper ZM2200K, ZM2200KU, ZM2500K, ZM2500KH, MZM2200KH, ZM5200M, ZM6100M Troubleshooting, Engine

Models: ZM2200K, ZM2200KU, ZM2500K, ZM2500KH, MZM2200KH, ZM5200M, ZM6100M ZM2500K, ZM2200K, ZM2200KU, ZM2500KH, MZM2200KH ZM522M, ZM6100M

1 32
Download 32 pages 37.3 Kb
Page 21
Image 21

TROUBLESHOOTING

PROBLEM

 

PROBABLE CAUSE

 

CORRECTIVE ACTION

 

 

 

 

 

 

Starter Will Not Crank

1. Battery dead.

1.

Service battery.

 

 

 

 

 

 

Engine

2. Blown fuse.

2.

Replace fuse.

 

 

3.

Electrical connections loose or corroded.

3. Clean and check connections for good contact.

 

 

 

 

 

 

 

 

4.

Defective ignition switch.

4.

Contact authorized SNAPPER dealer.

 

 

 

 

 

Engine Will Not Start

1. Blade engagement switch in the “ON” position.

1. Move blade engagement switch to “OFF”.

 

 

 

 

 

 

 

 

2.

Park brake not set.

2.

Set park brake.

 

 

 

 

 

 

 

 

3.

Fuel tank empty.

3.

Fill fuel tank with fresh fuel.

 

 

 

 

 

 

 

 

4.

Engine needs choking.

4.

Move choke control to “CHOKE” position.

 

 

 

 

 

 

 

 

5.

Spark plug wire disconnected.

5.

Place spark plug wire onto spark plug.

 

 

 

 

 

 

 

 

6.

Battery weak or dead.

6.

Service battery.

 

 

 

 

 

 

 

 

7.

Faulty parking brake, blade or ignition switch.

7.

Contact authorized SNAPPER dealer.

 

 

 

 

 

 

Engine Stalls After

1. Operator not in seat.

1.

Sit in operator’s seat.

 

 

 

 

 

 

Running

2. Choke control in the “CHOKE” position.

2.

Move choke control to “OFF” position.

 

 

 

 

 

 

 

 

3.

Fuel tank empty.

3.

Fill with fuel to proper level.

 

 

 

 

 

 

 

 

4.

Engine air pre-cleaner and or air cleaner dirty.

4.

Clean free of all debris.

 

 

 

 

 

 

 

 

5.

Spark plug defective or gap set improperly.

5.

Service spark plug.

 

 

 

 

 

 

 

 

6.

Fuel filter stopped up.

6.

Replace fuel filter.

 

 

 

 

 

 

 

 

7.

Water, debris or stale fuel in fuel system.

7.

Drain and clean fuel system.

 

 

 

 

 

 

Engine Loses Power

1. Excessive load on engine.

1.

Lessen load.

 

 

2.

Engine air pre-cleaner or air cleaner dirty

2.

Clean or replace filters.

 

 

 

 

 

 

 

 

3.

Engine oil level low.

3.

Fill with engine oil to proper level.

 

 

 

 

 

 

4. Engine cooling fins & air intake screen excessively dirty.

4. Clean cooling fins, air intake screen of all debris.

 

 

5.

Spark plug faulty.

5.

Service spark plug.

 

 

6.

Water, debris or stale fuel in fuel system.

6.

Drain and clean fuel system.

 

 

 

 

 

Engine Backfires When

1. Throttle control set too “FAST”.

1. Set throttle control to “SLOW” and allow engine

to

Turned To “STOP”

 

 

 

idle. Then, turn key to “OFF”.

 

Excessive Vibration

1. Damaged or bent mower blades.

1.

Service mower blade(s).

 

 

 

 

 

 

 

 

2.

Loose blade components.

2.

Service and tighten loose parts.

 

 

 

 

 

 

 

 

3.

Loose or missing air lift (if equipped).

3.

Replace air lifts. Tighten to proper torque.

 

 

 

 

 

 

 

(Trouble Shooting Continued on Next Page)

21

Page 21
Image 21
Snapper ZM2200K, ZM2200KU, ZM2500K, ZM2500KH, MZM2200KH, ZM5200M, ZM6100M Troubleshooting, Starter Will Not Crank, Engine