Manuals / Snapper / Lawn and Garden / Lawn Mower

Snapper ZM2500K, ZM2200K, ZM2200KU, ZM2500KH, MZM2200KH ZM522M, ZM6100M

Models: ZM2200K, ZM2200KU, ZM2500K, ZM2500KH, MZM2200KH, ZM5200M, ZM6100M ZM2500K, ZM2200K, ZM2200KU, ZM2500KH, MZM2200KH ZM522M, ZM6100M

1 32

Download 32 pages 37.3 Kb

Page 32

Image 32

Safety Instructions & Operator’s Manual for

MID MOUNT Z-RIDER

ZERO TURNING

HYDRO DRIVE

SERIES 0

IMPORTANT

Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings. Read, Understand, and Follow all warnings and instructions in this manual, the engine manual, and on the machine, engine and attachments. If you have any questions about your Snapper product, contact your local authorized Snapper dealer or contact Snapper Customer Service at Snapper, McDonough, GA. 30253. Phone: (1-800-935-2967).

WARNING: The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

SNAPPER INC.

MANUAL No. 4-6481 (REV. 2, 8/20/99)

Page 32

Image 32

Snapper ZM2500K, ZM2200K, ZM2200KU, ZM2500KH, MZM2200KH ZM522M, ZM6100M Mid Mount Z-Rider Zero Turning Hydro Drive Series

Contents

Safety Instructions & Operator’s Manual for POWER UNIT MODELSMID MOUNT Z-RIDER ZERO TURNING HYDRO DRIVE SERIES MOWER UNIT MODELSIMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS 2. Start engine from operators seat, if possible. Make sure blades are OFF and parking brake is setTABLE OF CONTENTS 1.2 NOMENCLATURE Section 1 - FAMILIARIZATION1.1 INTRODUCTION Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LISTSection 2 - OPERATING INSTRUCTIONS 2.2 STARTING & STOPPING - ENGINE, BLADES, PARKING BRAKE2.2.1. STARTING ENGINE 2.2.2. STOPPING ENGINESection 2 - OPERATING INSTRUCTIONS 2.2.5. PARKING BRAKEJOYSTICK IN NEUTRAL POSITION PARKING BRAKE LEVER IN ENGAGED “ON” POSITIONNOTE The engine does not have to be running to adjust cutting height Section 2 - OPERATING INSTRUCTIONSSection 3 - MAINTENANCE 3.2 SERVICE - AFTER FIRST 5 HOURS3.1 INTRODUCTION 3.2.2. CHECK MOWER BLADESection 3 - MAINTENANCE a. Lower deck to lowest setting b. Remove foot rest. See FigureSection 3 - MAINTENANCE 3. Power Transfer Shaft3.3.3. RIDING MOWER - LUBRICATION 1. Front Wheel Bearings 2. TransaxleSection 3 - MAINTENANCE 3.6 DECK REMOVALSection 3 - MAINTENANCE REAR LIFT ARM REAR LINK SHOULDERPLATE BOLT WASHER NUT THREADED ENDFRONT AXLE COTTER PIN WASHERS PULL BAR CLEVIS PIN TRANSFER SHAFT LOCK COLLAR TAKE OFF SHAFTSection 4 - ADJUSTMENTS & REPAIR DANGERSection 4 - ADJUSTMENTS & REPAIR 4.2.1. MOWER DECK ADJUSTMENT LEVELNESS ContinuedFRONT to REAR LEVEL FIGURE 4.2ASection 4 - ADJUSTMENTS & REPAIR PARKING BRAKE LEVER PARKING BRAKE RODNEW BLADE WEAR LIMIT NOTCH STARTS DANGEROUS CONDITION DO NOT USE ON MOWER REPLACE WITH NEW BLADESection 4 - ADJUSTMENTS & REPAIR 4.6 MOWER DRIVE BELT REPLACEMENT4.6.2. BELT REPLACEMENT 4.5.2. BLADE SHARPENINGSection 4 - ADJUSTMENTS & REPAIR 4.7 BATTERY 4.7.1. BATTERY REMOVALSection 4 - ADJUSTMENTS & REPAIR Battery Condition ChartTROUBLESHOOTING Engine Loses PowerStarter Will Not Crank EngineTROUBLESHOOTING Battery Will Not ChargeTractor Will Not Move Loss Of TractionSERVICE SCHEDULE MAINTENANCE PARTSMAINTENANCE/REPLACEMENT PARTS 52” MOWER DECK2 YEAR LIMITED WARRANTY PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE Page Page Page Safety Instructions & Operator’s Manual for MID MOUNT Z-RIDER ZERO TURNING HYDRO DRIVE SERIES