Electric
Supply voltage: 534090 | 208V/3ph/60Hz |
534091 208V/3ph/60Hz
534092 240V/3ph/60Hz
534093 240V/3ph/60Hz
Dishwasher has three selectable hot water booster configurations according to inlet water supply temperature.
Dishwasher requires two separate electrical service connections. Connection 1 for Hot Water Booster; Connection 2 for running of the machine (wash pump, tank heat, conveyor drive motor, rinse booster pump, electronic control). Refer to the information below for Amp requirements.
Booster 40 °F rise Electrical Characteristics
Hot Water Booster Amp Load Connection 1:
208 V/3p/60Hz | 33.35A (12 kW) |
240 V/3p/60Hz | 28.9A (12 kW) |
Wash Pump, Tank heat Amp Load Connection 2:
208 V/3p/60Hz | 64A (21 kW) |
240 V/3p/60Hz | 57.5A (21 kW) |
Total Amp Load: 208 V/3p/60Hz | 97.4A (33 kW) |
240 V/3p/60Hz | 86.4A (33 kW) |
Booster 70 °F rise Electrical Characteristics
Hot Water Booster Amp Load Connection 1:
208 V/3p/60Hz | 50A (18 kW) |
240 V/3p/60Hz | 43.3A (18 kW) |
Wash Pump, Tank heat Amp Load Connection 2:
208 V/3p/60Hz | 64A (21 kW) |
240 V/3p/60Hz | 57.5A (21 kW) |
Total Amp Load: 208 V/3p/60Hz | 114A (39 kW) |
240 V/3p/60Hz | 100.8A (39 kW) |
Booster 100 °F rise Electrical Characteristics
Hot Water Booster Amp Load Connection 1:
208 V/3p/60Hz | 66.6A (24 kW) |
240 V/3p/60Hz | 57.7A (24 kW) |
Wash Pump, Tank heat Amp Load Connection 2:
208 V/3p/60Hz | 64A (21 kW) |
240 V/3p/60Hz | 57.5A (21 kW) |
Total Amp Load: 208 V/3p/60Hz | 130.6A (45 kW) |
240 V/3p/60Hz | 115.2A (45 kW) |
Warewashing
66″ Single Tank Conveyor Dishwasher
with Built In Hot Water Booster WT66
Water
Inlet Water supply pressure: | 22 – 102 psi (150 – 700 kPa) |
Inlet Cold Water Supply Temperature |
|
for pre wash section: |
Inlet Hot Water Supply Temperature for wash/rinse section (booster size can be set on site during installation):
| 140 °F (60 °C) |
| with booster set as 40 °F rise. |
| 110 °F (44 °C) |
| with booster set as 70 °F rise. |
| 80 °F (27 °C) |
| with booster set as 100 °F rise. |
Inlet Water supply hardness: | 4 - 8 gpg |
Incoming Cold Water line size | G 3/4″ |
(pre wash): | |
Incoming Hot Water line size | G 3/4″ |
(wash/rinse section): | |
Drain line size (pre wash section): | G |
Drain line size (wash/rinse section): | G |
Water consumption: Gallons/hr: | 83.2 gal/hr (315 liters) |
Water consumption/rack: | 0.4 gal/rack (1.5 l/rack) |
Pre wash temperature: | < 105 °F (<40 °C) |
Pre wash tank size: | 11.8 gal (45 liters) |
Pre wash pump power: | 0.5 hp (0,37 kW) |
Pre wash pump water flow: | 39 gal/min (150 l/min) |
Wash temperature: | 160 – 172 °F |
Wash tank size: | 26 gal (100 liters) |
Wash pump power: | 2 hp (1.5kW) |
Wash pump water flow: | 118.9 gal/min (450 l/min) |
Rinse temperature: | 180 – 194 °F |
Rinse pump power: | 0.4 hp (0.32 kW) |
Rinse pump water flow: | 1.32 gal/min (5 l/min) |
Hot water booster capacity: | 6.2 gal (24 liters) |
Initial fill Hot Water requirements: | 32.2 gal (124 liters) |
Initial fill Cold Water requirements: | 11.8 gal (45 liters) |
Exhaust Requirements
Unit supplied as standard with extended vent hoods (can be removed during installation if not required). Exhaust extraction not more than 160 CFM
Refer to installation diagram for minimum exhaust hood installation height .
Key Information
Productivity racks per hour | 200 racks / 3600 dishes |
(max speed): | (average 18 dishes per rack) |
Productivity racks per hour | 130 racks / 2340 dishes |
(min speed): | (average 18 dishes per rack) |
Table to Table connection: | 66″ (1676 mm) |
Number of Tanks: | 1 |
Height with door open: | |
Charging hole size (width): | |
Charging hole size (height): | |
Net weight: | 1012 lb (459 kg) |
Shipping weight: | 1210 lb (549 kg) |
Shipping width: | |
Shipping depth: | |
Shipping height: | |
Shipping volume: | 143 cu.ft (4.05 m3) |
Noise level: | <70 dBA |
Unit predisposed to accept external detergent dispensers, detergent probes and rinse aid dispensers.