Table of Contents |
| |
1. | Components and Parts | 6 |
2. | Please Read First! | 7 |
3. | Safety | 7 |
3.1 | Specified Conditions of Use | 7 |
3.2 | General Safety Instructions | 7 |
3.3 | Symbols Used | 7 |
4. | Operation | 7 |
4.1 | Before Initial Operation | 7 |
4.2 | Using the Tool | 7 |
5. | Care and Maintenance | 8 |
6. | Available Accessories | 8 |
7. | Repairs | 8 |
8. | Environmental Protection | 8 |
9. | Technical Specifications | 8 |
2. Please Read First!
These instructions are written in a way to let you work with the tool quickly and safely. Here is how to use the instruc- tions:
•Read these instructions fully before operating the tool. Pay special attention to the safety information.
•If you notice transport damage while unpacking, notify your supplier immediately. Do not operate the tool!
•These operating instructions are intended for people with basic tech- nical knowledge regarding the ope- ration of a tool like this or similar air tools. Inexperienced persons are strongly advised to seek competent advise and guidance from an experi- enced person before operating this tool.
•Keep all documents supplied with this tool for future reference. Also, retain proof of purchase in case of a warranty claim.
•This tool must not be sold or lent to someone else without being accom- panied by these operating instruc- tions and all other documents sup- plied with the tool.
The manufacturer is not liable for any damage caused by the
Information in these instructions is deno- ted as under:
Danger!
Risk of personal injury or environmental damage.
Caution!
Risk of material damage.
−At times numbers are used in illust- rations (1, 2, 3, ...). These numbers:
−indicate component parts;
−are consecutively numbered;
−Numbered steps must be carried out in sequence.
−Instructions which can be carried out in any order are indicated by a bullet point (•).
−Listings are indicated by a dash
3. Safety
3.1Specified Conditions of Use
This tool is used for running, driving and removing nuts and bolts.
With this ratchet wrench bolts may only be tightened up to the air tool's maxi- mum torque.
This tool shall only be powered by an air compressor. The max. permissible wor- king pressure stated in the Technical Specifications must not be exceeded. This tool must not be operated with gases that are explosive, combustible or detrimental to health.
Any other use is not as specified. Use not as specified, modification of the tool or use of parts not approved by the manufacturer can cause unforeseeable damage!
3.2General Safety Instruc- tions
•When using this air tool observe the following safety instructions to mini- mize the risk of personal injury or material damage.
•Please also observe the special safety instructions in the respective chapters.
•Observe the statuary accident insu- rance institution regulations and regulations for the prevention of accidents pertaining to the operation of air compressors and air tools, where applicable.
AGeneral danger!
•Keep your work area tidy – a messy work area invites accidents.
•Be alert. Do not operate this tool while under the influence of drugs, alcohol or medication.
•Keep the tool from jamming – ensure firm footing when using the tool.
•Always use a quick coupler to con- nect this air tool to a compressor.
•Make sure that the max. permissible working pressure stated in the Tech- nical Specifications is not exceeded.
ENGLISH
•Do not overload tool – use it only within the performance range it was designed for (see Technical Specifi- cations).
•Do not touch any rotating parts.
•Disconnect tool from air supply before changing sockets or if left unattended.
AHazard generated by insuffi- cient personal protection gear!
•Wear hearing protection.
•Wear safety glasses.
AHazard generated by tool defects!
•Do not attempt to repair the tool yourself! Only trained specialists are permitted to service or repair com- pressors, pressure vessels and air tools.
A Caution!
Protect the tool, air inlet, square drive and operating elements in particular, from dust and dirt.
3.3Symbols Used
Danger!
Neglect of the following warnings may cause seri- ous injury or material damage.
Read instructions.
Wear hearing protection.
Wear safety goggles.
4. Operation
4.1Before Initial Operation
•Install the plug nipple.
4.2Using the Tool
A Caution!
To ensure a long service life of this tool, it needs to be supplied with suf- ficient quantities of pneumatic oil. This can be achieved by:
−a service unit with oiler at the compressor.
−a lubricator, installed directly on the air tool or in the air line.
7
