Custom Made Sink Products
List Price CUSL-31
Effective: December 4, 2006
(Supersedes
ELKAY POINTS OF SUPERIORITY
1.Elkay “Lusterton” Custom Cabinet Sink and Countertops are fabricated of #18 gauge nickel bearing
2. | Intersections where sink bowls meet drainboards are rounded to | HEIGHT OF BACK |
FROM TOP OF | ||
| sanitary radii. | RAISED RIM |
3. | Drainboard, sink bowls, raised rims and backsplash are welded, | *1 1/2" |
|
ground and polished smooth to a
4.All corners in sink bowls (horizontal and vertical) are rounded to 1
5.Drainboards have large,
6.Entire underside of sink top and bowl is fully undercoated to dampen sound and prevent condensation.
7.Superior surface finish and satin luster achieved through special hand polishing operations by master craftsmen.
HOW TO MEASURE
1.Measure, in inches, along wall or walls where top is to be installed.
2.Establish overall counter width, front to back, (standard is 25"), including backsplash thickness.
3.Determine height of backsplash (measured from top of raised rim.)* (Standard is 4") Determine thickness of backsplash, (Standard is 1 1/2").
4.Determine sink bowl size and its location. (See pages 4 and 5.)
5.List special features such as range cutout, return ends, rounded corners, etc. (See pages 6 and 7.)
*Explanatory Note:
Elkay Custom Sink Tops and Countertops are provided with our standard 5/32" raised rim. Flat rim is available at no additional charge. For rims other than 5/32" or flat, please refer to Custom Feature #17 on page 7.
Illustration A
Limitation profile of sink when |
| Limitation profile of sink when | |||
wall faucets are used. |
| deck faucets are used. |
| ||
|
|
|
|
|
|
2" MIN. | HEIGHT OF BACK |
| 2" MIN. |
| |
|
|
|
| ||
1 1/2" MIN. | FROM TOP OF |
|
| BOWL INSIDE | 3 3/4" |
RAISED RIM |
|
| |||
|
|
|
|
| MIN |
| *1 1/2" |
|
| 3/4" OR | |
|
| |
|
| MORE |
BACKSPLASH |
| |
| (1 1/2" STD.) | |
USUALLY 1 1/2" |
| |
|
| |
THICK TO ALLOW |
|
|
|
| |
FOR SUPPLY LINES |
|
|
|
|
|
* 1 1/4" top thickness can be furnished when specified at no additional cost.
Illustration B
Underside view of construction detail | 18 GA. STAINLESS STEEL TOP | |
EXCEEDS 1/8" | 14 GA. STEEL PLATE |
|
THICKNESS | REINFORCING |
|
WOOD STRIP
3/4" X 3/4" X 1/8" | BOWL |
ANGLE IRON |
|
|
UNDERSIDE IS FULLY UNDERCOATED TO
DAMPEN SOUND AND PREVENT CONDENSATION.
STAINLESS STEEL TOP
WOOD STRIP
Illustration C
HOW TO ORDER
1. | When ordering Elkay custom made stainless steel sink and countertops, |
| accuracy of dimensions is of the utmost importance. |
2. | Furnish a sketch of sink or counter arrangement marked with proper |
| dimensions, and special features. Remember, you cannot give too |
| much information. |
3. | Always include the following information: |
| a) Show dimension from end of counter to center line of single |
| compartment sink models…or |
| b) Show dimension from end of counter to center line of partitions of two or |
| more compartment sink models. |
| c) Specify model number of faucet and other trim desired, if not included |
| with the sink model chosen. |
| d) Indicate manufacturer’s name and complete model number of range unit |
8"
12"
PARTIAL
COLUMN CUT
(f)
54"
FIELD JOINT
(a)
96"
(e)
126"
63"
(c)(c)
2 1/8"
This is an example of pricing a custom made unit. The sink is Model LR3722, double compartment, top has 4" high backsplash and top has a flat rim.
8" 12"
4"
FULL
COLUMN CUT
(g)
WELD
(b)
60"
to be installed if applicable. |
e) Indicate and locate all cutouts or special conditions you require. |
(See pages 6 & 7.) |
HOW TO PRICE
For Basic Counter Tops up to 25" wide
1.Add all wall dimensions to determine total linear inches of counter. From Schedule for Countertops on page 3 locate total inches column one. Under proper backsplash height column, read total price of basic counter.
2.When sink bowl is desired, add to price of basic counters, the price of sink model chosen, as shown on pages 4 and 5 (custom sizes are available).
3.Add the price of all special features applicable, as shown on pages 6 and 7.
12" RADIUS
(d)
25"
25"
Wall Dimensions (4" Backsplash)
96"+ 126"+ 60"= 282":
Base 156" . . . . . . . . . . . . . . . .$ 3,041.00 Additional 126" @ $18.00 . . . . . . . . . . . . . . .2,394.00
(a) Field Joint w/4" back . . . . . . . . . . . . . . . . . .903.00
(b) “U" Weld w/4" back . . . . . . . . . . . . . . . . . . .722.00
(c) LR3722 Double Bowl . . . . . . . . . . . . . . . .1,621.00
(d) 12" Radius Calculations
Base 3" . . . . . . . . . . . . . . . . . . . .135.00 Additional 9" @ $26.00 . . . . . . . . . . . .252.00
(e) Range Cutout . . . . . . . . . . . . . . . . . . . . . . .304.00
(f) Partial Column Cut . . . . . . . . . . . . . . . . . . .311.00
(g) Full Column Cut . . . . . . . . . . . . . . . . . . . . .549.00
TOTAL LIST PRICE . . . . . . . . . . . . . . . . . . .$10,232.00
2 | All dimensions are in inches. To convert to millimeters, multiply inches by 25.4. |