INSTRUCTION MANUAL

CF100 STAINLESS STEEL CHOCOLATE FOUNTAIN

Dear Customer,

Please read these Operating Instructions through carefully before connecting your device to the mains, in order to avoid damage due to incorrect use. Please pay particular attention to the safety information. If you pass the device on to a third party, these Operating Instructions must also be handed over.

COMPONENTS

1.

Fountain cap

 

2.

Hole

1

3.

Transport spindle

 

4.

Retaining pivot

 

5.

Motor wave

 

6.

Power cable with power plug

2

7.

Turn switch 0/I/II

8.

Control light

 

9.

Height-adjustable stand

3

10.

Bowl

 

than 30 mA in the house installation. Please consult your installing electrician

The cable as well any extension cable required should be laid such that there will not be any risk of anyone pulling it inadvertently or tripping over it.

If a long extension cable is used, it must be suitable for the power supply in question. Otherwise it causes overheating of the cable and/ or plug.

Set the unit on a rigid, flat and heat-proof surface, not near open flames (such as gas oven) and operate it out of reach of children.

This appliance is suitable neither for commercial use nor for use outdoors.

Children cannot sense the dangers caused by improper handling of electrical devices.

Do not, therefore, let children use household devices, except under supervision.

Pull out the plug out of the socket, when the appliance is not in use and also before cleaning.

Caution! The appliance is on power so long as it is connected to the power circuit.

Switch off the unit before pulling out the mains plug.

Use only spare parts from the manufacturer or his local dealer.

Never carry the unit by its power cord.

Do not remove individual housing components.

SPECIAL SAFETY ADVICE

10

9

4

5

6

Danger of fire!

Parts of the appliance will become hot during operation; therefore do not move the appliance while operating.

Do not leave the appliance unattended when it is turned on.

The appliance may only be used for chocolate.

During operation, the power cable may not come in contact with hot parts of the appliance.

BEFORE INITIAL USAGE

Remove all packaging material.

Clean and dry the appliance as described under Cleaning and Care.

USAGE

8 7

SAFETY INFORMATION

Wrong operation and improper handling can cause problems with the appliance and injury to the user.

The unit may be used only for the intended purposes. No liability is accepted for damages arising from improper use or faulty handling.

Before connecting to the mains, please check whether the type of supply and the mains voltage match with the details given on the nameplate on the appliance.

Do not immerse the appliance and mains plug in water or other fluids. Should the appliance still fall in water some time, pull out the power plug immediately and have the appliance checked by an expert before using it again. There is danger to life from electrical shock!

Do not try to open the housing yourself! Do not introduce any kind of objects into the housing.

Do not use the appliance with wet hands, on moist floor or when the ambience is humid.

Do not hold the mains plug with wet or moist hands.

Check the mains plug and mains adapter regularly for damages. In case of damages, have the power cord and mains plug changed by the manufacturer, or a qualified expert, in order to avoid danger.

Do not operate the appliance, if power cable or the mains plug shows damage or the unit falls to the floor or has been damaged otherwise. In such cases, bring the unit to the workshop for checking and repairs, if necessary.

Do not ever try to repair the unit yourselves. There is danger from electrical shock!

Do not let the power cord hang over sharp edges and keep it away from hot objects and open flames. Pull the plug itself to remove it from the plug socket.

Installation of a spike protector will offer additional protection with a nominal trigger current of not more

5

Preparation

Place the appliance on an even surface.

The chocolate fountain must remain horizontal, to ensure a nice flow of chocolate. To balance the eventual unevenness, the stand (9) can be unscrewed.

Place the fountain cap (1) on the bowl in such a way that the three pivots (4) fit into the corresponding holes (2).

Place the transport spindle from above through the opening of the fountain cap (1), so that the motor wave

(5) reaches the transport spindle.

Connect the power plug to an outlet.

To warm up the appliance (about 3-5 minutes), turn the turn switch 0/I/II (7) to position I. The control light (8) will light up.

Preparation of chocolate

Any kind of chocolate can be used.

However, it is easiest to use baking chocolate or melting chocolate.

In the case that normal bar-chocolate is used, oil (e.g. sunflower oil) must be added to achieve the appropriate viscosity of the chocolate.

Break the chocolate which will be used, about 500 g, into small pieces, and melt it in a designated container in the microwave or on stovetop.

Next, add oil so that the appropriate viscosity is reached. The chocolate should flow easily from a spoon.

As a point of reference, about ? cup of oil is needed for 3 cups of chocolate.

During preparation, stir the chocolate for 30 seconds, until it is completely liquidities.

6

Page 4
Image 4
Elta CF100 Stainless Steel Chocolate Fountain, Components, Special Safety Advice, Before Initial Usage

CF100 specifications

The Elta CF100 is a state-of-the-art radar system designed for advanced air defense applications and surveillance missions. Known for its robust capabilities and cutting-edge technology, the CF100 plays a pivotal role in modern military and defense operations, offering unparalleled performance in various environments.

One of the standout features of the CF100 is its multi-mode capability, which allows it to perform a range of functions including air surveillance, target tracking, and fire control. This versatility enables operators to adapt the system to meet diverse operational requirements, whether monitoring air traffic or supporting ground-based air defense systems.

The CF100 employs advanced phased array radar technology that enhances its detection and tracking capabilities. The electronically scanned array allows for rapid beam steering, which means it can quickly switch attention between multiple targets without the need for mechanical movement. This results in a higher probability of detecting fast-moving aerial threats while simultaneously tracking multiple targets efficiently.

Another notable characteristic of the CF100 is its high-resolution imaging system. Leveraging synthetic aperture radar (SAR) technology, the CF100 delivers detailed ground imagery, which is crucial for intelligence, surveillance, and reconnaissance (ISR) missions. This capability significantly improves situational awareness and aids in decision-making processes for commanders on the ground.

The CF100 integrates advanced signal processing algorithms that enhance target discrimination, reducing the likelihood of false alarms and ensuring that operators can focus their efforts on legitimate threats. This is complemented by a suite of electronic warfare features, which improve survivability in contested environments and enhance overall operational effectiveness.

Furthermore, the CF100 is designed with interoperability in mind. It can seamlessly integrate with existing command and control systems, allowing for coordinated operations across various platforms and branches of the military. This interoperability is crucial for joint operations, where information sharing and situational awareness are paramount.

In terms of deployment, the CF100 is built to withstand harsh environmental conditions, making it suitable for use in diverse geographical regions and operational scenarios. Its rugged design ensures reliable performance, whether deployed in desert, arctic, or coastal environments.

In summary, the Elta CF100 is a highly capable radar system that combines advanced technologies with robust features. Its multi-mode functionality, phased array technology, high-resolution imaging, and electronic warfare capabilities make it an ideal choice for modern air defense and surveillance applications, ensuring that military forces can maintain superiority in increasingly complex operational landscapes.