Emerson CF2400BZH00, CF2400BC00, CF2400AB00 How to Wire Your Ceiling Fan, Listed Wire Connector

How to Wire Your

Ceiling Fan

If you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician.

!WARNING

Turning off wall switch is not sufficient. To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. All wiring must be in accordance with National and Local codes and the ceiling fan must be properly grounded as a precaution against possible electrical shock.

1.If you are going to use an Emerson Remote Control/Receiver or Wall Control/Receiver to operate your ceiling fan, wire your fan in accordance with the Control/Receiver Owner’s Manual. (NOTE: The wire from the uplight harness is orange instead of yellow.) After wiring, return to Step 4 below.

2.If you are going to use two wall switches or Emerson Fan/Light Controls, you will need a three-wire (with ground) conductor cable between the ceiling and wall outlet boxes. This will allow you to operate the uplight and optional Emerson Light Fixture (if installed) from one switch/control and the ceiling fan from a separate switch/control. (Refer to the Emerson Fan/Light Control Owner’s Manual.) Refer to Figure 10 and proceed as follows:

a.Connect the green grounding lead from the hanger ball and the green grounding lead from the hanger bracket to the supply grounding conductor (this may be a bare wire or wire with green colored insulation). Securely connect wires with a wire connector (supplied).

b.Securely connect the fan motor white wire to the supply white (neutral) wire using a wire connector (supplied).

c.Securely connect the fan motor black wire to the supply black (hot) wire using a wire connector (supplied).

d.Securely connect the fan motor blue wire to the supply red (hot) wire using a wire connector (supplied).

e.After connections have been made, separate the white and green wires from the black, blue and red wires.

f.Carefully turn the wires upward and insert them up through the open side of the hanger bracket and into the outlet box. Push the green and white wires into one side of the outlet box; push the black, blue and red wires into the other side of the outlet box.

! WARNING
Check to see that all connections are tight,
including ground, and that no bare wire is visible
at the wire connectors, except for the ground wire.
Do not operate fan until blades are in place. Noise
and fan damage could result.	7

				EMERSON FAN CONTROL
LISTED OUTLET BOX			BLACK FAN WIRE
GREEN WIRE
		BLACK	RED	LIGHT		BLACK
(GROUND)				CONTROL
						(HOT)
FROM
						TO 120
HANGER
BRACKET						VOLT
			WHITE		WHT.	SUPPLY
GROUND
WIRE				GROUND	GROUND
			BLUE
		GREEN WIRE (GROUND)		THREE-CONDUCTOR CABLE (WITH
				GROUND) BETWEEN CEILING AND
Figure 10		FROM HANGER BALL		WALL OUTLET BOXES
	LISTED WIRE CONNECTOR (4)

3.If you are going to use a single wall switch to control your ceiling fan, uplight, and optional Emerson Light Fixture (if installed) simultaneously, you will need a standard two-wire (with ground) conductor cable between the ceiling and wall outlet boxes. The fan speed and uplight can then be operated from the pull chain switches in the switch housing; the optional light fixture can be operated from the light fixture switch. Refer to Figure 11 and proceed as follows:

aConnect the green grounding lead from the hanger ball and the green grounding lead from the hanger bracket to the supply grounding conductor (this may be a bare wire or wire with green colored insulation). Securely connect wires with a wire connector (supplied).

b.Securely connect the fan motor white wire to the supply white (neutral) wire using a wire connector (supplied).

c.Securely connect the fan motor black wire and blue wire to the supply black (hot) wire using a wire connector (supplied).

d.After connections have been made, separate the white and green wires from the black and blue wires.

e.Carefully turn the wires upward and insert them up through the open side of the hanger bracket and into the outlet box. Push the green and white wires into one side of the outlet box; push the black and blue wires into the other side of the outlet box.

!WARNING

Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire connectors, except for the ground wire. Do not operate fan until blades are in place. Noise and fan damage could result.

LISTED OUTLET BOX BLACK FAN WIRE		GENERAL USE
GREEN WIRE	BLACK	ON/OFF
(GROUND)		WALL SWITCH BLACK
FROM		(HOT)
HANGER		TO 120
BRACKET		VOLT
	WHITE	SUPPLY
GROUND		WHT.
WIRE		GROUND GROUND
	BLUE
	GREEN WIRE (GROUND)	TWO-CONDUCTOR CABLE (WITH
		GROUND) BETWEEN CEILING AND
	FROM HANGER BALL	WALL OUTLET BOXES
Figure 11 LISTED WIRE CONNECTOR (3)