IMPORTANT

Your ceiling fan is designed to be installed either in the standard manner, or in the close-to-the-ceiling manner. Using the standard method, the hanger ball/downrod assembly will suspend the fan several inches below the ceiling cover. Using the close-to-the-ceiling method, the ceiling cover installs directly on the fan motor housing, thus mounting the fan 3-1/2 inches closer to the ceiling than the standard method. In no

DECORATIVE

CAP

HAIRPIN

CLIP

MOTOR COUPLING

HANGER BALL/DOWNROD ASSEMBLY

CEILING

COVER

SETSCREW

CLEVIS

PIN

case should the fan blades be lower than seven feet above the floor. Depending on your desired mounting method, proceed to

“INSTALLING HANGER BALL/DOWNROD ASSEMBLY” for standard mounting, or to

“INSTALLING CEILING COVER ON FAN MOTOR HOUSING” for close-to-the-ceiling mounting.

SETSCREW

Figure 1

Installing The Hanger

Installing The Ceiling Cover

Ball/Downrod Assembly

On The Fan Motor Housing

(For Standard Mounting)

(For Close-to-the-Ceiling Mounting)

1.Pass the 56" motor leads through the opening in the ceiling cover. Be sure the cover is oriented correctly.

2. Separate, untwist and unkink the three motor leads. Route the motor leads through the hanger ball/downrod assembly.

3.Loosen the two setscrews in the motor coupling. Align the clevis pin holes in the downrod with the holes in the motor coupling. Install the clevis pin and secure with the hairpin clip (Figure 1). The clevis pin must go through the holes in the motor coupling and the holes in the downrod. Be sure to push the straight leg of the hairpin clip through the hole near the end of the clevis pin until the curved portion of the hairpin clip snaps around the clevis pin. The hairpin clip must be properly installed to prevent the clevis pin from working loose. Pull on the hanger ball to make sure the clevis pin is properly installed.

! WARNING

It is critical that the clevis pin in the motor coupling is properly installed and the setscrews securely tightened. Failure to verify that the pin and setscrews are properly installed could result in the fan falling.

1.Remove and retain three screws from the top of the motor housing (Figure 2A).

2.Position the rubber gasket (supplied in parts bag) on the motor housing (small holes in gasket centered over the screw holes in the housing) (Figure 2B).

REMOVE SCREWS (3)

INSTALL GASKET

Figure 2A

Figure 2B

3.Gently pry the decorative cap (Figure 1) from the ceiling cover. Align the holes in the ceiling cover with the holes in the motor housing and secure using the three screws (Figure 3).

4.While pulling up on the hanger ball, securely tighten the two setscrews in the motor coupling (Figure 1).

NOTE: The setscrews must be properly installed as described above, or fan wobble could result.

5.The fan comes with blue, black and white leads that are 56” long. Measure up approximately 6 to 9-inches above top of hanger ball/downrod assembly. Cut off excess leads and strip back insulation 1/2-inch from end of leads.

4

RUBBER

SCREW (3)

GASKET

 

Figure 3

4.The fan comes with blue, black and white leads that are 56” long. Measure up approximately 6 to 9-inches above the motor coupling. Cut off excess leads and strip back insulation 1/2-inch from ends of leads.

Page 3 Page 5
Page 4
Image 4
Emerson CF711WB00, CF710PB00, CF710AW00, CF710BS00, CF711PB00 For Standard Mounting For Close-to-the-Ceiling Mounting
Page 3 Page 5

CF711CK00, CF711BS00, CF711WW00, CF710AW00, CF711AW00 specifications

The Emerson CF710PB00, CF710BS00, CF710WW00, CF711WB00, and CF711AB00 are part of the renowned Emerson ceiling fan series, known for their blend of style, efficiency, and cutting-edge technology. These models cater to a variety of aesthetic preferences and room sizes, making them versatile choices for modern homes and commercial spaces.

One of the standout features across these models is their stunning design. The CF710 series, available in a range of finishes including polished bronze (CF710PB00), brushed steel (CF710BS00), and white (CF710WW00), offers options that fit seamlessly into any interior décor. The CF711 series further expands on this with the walnut blades of the CF711WB00 and the antique brass finish of the CF711AB00, ensuring there’s a fan for every taste.

In terms of performance, these fans are equipped with powerful yet quiet motors that ensure optimal air circulation without the disruptive noise often associated with traditional ceiling fans. The energy-efficient DC motor technology used in these models not only reduces energy consumption but also allows for a wider range of speed settings. This feature affords users precise control over airflow, making it easy to tailor the environment to their preferences.

Another notable characteristic is the ease of installation, which is a hallmark of Emerson fans. Each model comes with comprehensive instructions and mounting hardware, enabling quick and straightforward setup. Additionally, the fans are compatible with various control options, including pull chains, wall switches, and remote controls, enhancing their user-friendliness.

Moreover, these fans exhibit durability and longevity thanks to their high-quality materials and construction. The blades are designed to withstand the test of time while providing a stylish aesthetic. Some models feature energy-saving LED lighting, providing both illumination and ambience in any room.

In summary, the Emerson CF710PB00, CF710BS00, CF710WW00, CF711WB00, and CF711AB00 ceiling fans are ideal for those seeking efficient cooling solutions paired with stylish designs. With their combination of performance, aesthetic versatility, and user-friendly technology, these models reflect Emerson's commitment to quality and innovation in home comfort. They stand out not just as functional devices but as integral elements that enhance the overall home experience.
Top Page Image Contents