Emerson EM529S owner manual Drive Safe, Box, Location of controls, Charging the headset

Drive Safe About noise cancellation technology

Manual Pairing

OR depending on which model mobile phone you are trying

WIRELESS HEADSET

CAUTION: Although this device enables drivers to conduct handsfree conversations, it is still safer to pull over before using a mobile phone.

Always keep your full attention on your driving.

Driving while talking on your mobile phone is dangerous, and illegal in many states.

Check local laws regarding the use of a mobile handset and wireless headset while driving. If you use the Bluetooth Headset while driving, ensure your attention and focus remains on your driving.

Please use your mobile phone, and our

product responsibly while driving!

This headset uses a dual microphone design to ￿lter out wind and unwanted external noise.

Using Noise Cancellation Technology, the headset compares the sound from the twin, built-in microphones, and is able to recognize the di￿erence between voice and unwanted background noise.

Noise cancel microphone 1

1.Make sure the Bluetooth Headset is within 3 feet of your mobile phone or Bluetooth enabled device.

2.Set the [Power] switch to the ON position.

3.Press and HOLD the [Call] button until the indicator light ￿ashes RED and BLUE alternately.

4.The headset is now in Pairing Mode and is ready to connect to your mobile phone or Bluetooth enabled device.

Power Switch

Power ON/OFF

(Green = ON, Red = OFF)

to connect the headset to, it may not be necessary to enter a passcode and the following message (or similar) may appear on your phone’s display.

Bluetooth: Enabled

Paired Devices:

EM529

“EM529” would like to pair with your phone. Would you like to allow it to pair?

Cancel Pair

Select “Pair” to complete the pairing process.

Owner’s Manual

Model: EM529S

In the box

WIRELESS HEADSET

Owner’s Manual

Model: EM529S

Owner’s

Manual

Bluetooth

Headset

S M L

Silicone cushions

Location of controls

Power Switch
Power ON/OFF
(Green = ON, Red = OFF)
Noise cancel	Speaker/
	Silicone cushion
microphone 1
Call button
Answer/end a call	Volume Up
Indicator
light	Volume Down
Charging
socket	Microphone
Noise cancel
microphone 2

Charging the headset

NOTE: Charge the headset for at least 8 hours beforeusing it for the ￿rst time, even if the RED LED indicator shuts o￿.

1.Connect the small end of the USB cable to the charging socket of the headset.

2.Connect the other end of the USB cable to either the:

•AC Charger, and plug into a wall (A/C) outlet

•Computer’s USB port

•Car Charger

3.The RED LED indicator light turns on while the headset is charging.

4.The RED LED indicator light shuts o￿ when the headset is fully charged (approximately 2-3 hours).

NOTE: When the battery is running low, the RED LED indicator

light starts to ￿ash along with a warning beep.

Noise cancel microphone 2

Noise Cancellation Technology

Enables the other end of your conversation to hear you clearly!

Pairing the headset

Easy Pairing

(First time pairing only)

Please read through this section before turning the device on. We recommend reading this manual in it’s entirety before pairing the headset for the ￿rst time.

This Bluetooth headset has an “Easy Pairing” feature which sets the headset to Pairing Mode the ￿rst time the power switch is turned on.

1.Make sure the Bluetooth Headset is within 3 feet of our mobile phone or Bluetooth enabled device.

within 3 feet

Indicator light

Red and Blue ￿ashing

within 3 feet

Indicator light

Red and Blue ￿ashing

NOTE: To enter Pairing Mode at any time, you must press and HOLD the [Call] button for approximately 10 seconds.

Continue here from “Easy Pairing”

5. Set your mobile phone to search for Bluetooth devices.

Bluetooth: Enabled

Paired Devices:

*Empty *

Searching for devices

1found Stop

6.When the phone ￿nds the headset, con￿rm by selecting EM529 from the list.

Bluetooth: Enabled

Paired Devices:

EM529

Select Device:

EM529

Cancel

8.Your mobile phone will con￿rm that the pairing process was completed and prompt you to accept the connection. Please select “YES” to connect the headset to your mobile phone. If the pairing was successful, the headset’s blue indicator light turns to standby mode and ￿ashes once every three seconds.

Bluetooth: Enabled

Paired Devices:

EM529

Confirm connection to

EM529?

YES / NO

9.When attempting to reconnect the headset to your mobile phone, you may see the message below and your mobile phone will prompt you to accept the connection request to the EM529 headset, and an option not to ask this again. Please accept the connection, and if you select“Don’t ask this again”, your phone will automatically accept future connection requests from the headset.

Bluetooth: Enabled

Paired Devices:

EM529

Accept connection request from EM529?

YES / NO

Don’t ask this again

USB charging

cable

Earhook

AC charger

Stereo earphone Car Charger

USB cable

Indicator

light

Charging

Socket

Headset

AC Charger PC Car Charger

Power Switch

Power ON/OFF

(Green = ON, Red = OFF)

2.Set the [Power] switch to the ON position. The indicator light should be ￿ashing RED and BLUE alternately, indicating the headset is in Pairing Mode and ready to connect to your Bluetooth enabled device.

3.Continue to“Manual Pairing” step 5 shown in the next column.

NOTE: Manual Pairing

If the ￿rst time pairing was unsuccessful or for future pairing, you will need to manually pair the headset to your Bluetooth enabled device (see“Manual Pairing” step 1 in the next column ).

7. Enter the passcode “0000” when prompted by the phone.

Bluetooth: Enabled

Paired Devices:

EM529

Enter numeric passkey for EM529:

0000

OK

NOTE: The screenshots above are typical of many Bluetooth enabled phones in the market today, and are used to assist in the explanation of the pairing process. Your mobile phone’s or Bluetooth enabled device’s interface and interaction with the headset may be slightly di￿erent from the illustrations shown.