L
Y
Pb
Pr
R
L
VIDEO2
AUDIO
R
VIDEO1
S-VIDEO
VIDEO
HEAD PHONE
ANT
AUDIO
COMPONENT
VIDEO2
R
L
Y
Pb
Pr
AUDIO
COMPONENT
R
L
VIDEO
S-VIDEO
ANT
AUDIO
VIDEO1
HEAD PHONE
Component
Video Cable
Audio Cable
Video Game
Video Camera
Rear of this TV
ex. (OUT)
(OUT)
(IN)
(IN)
L
Y
Pb
Pr
R
L
VIDEO2
AUDIO
R
VIDEO1
S-VIDEO
VIDEO
HEAD PHONE
ANT
AUDIO
COMPONENT
VIDEO2
R
L
Y
Pb
Pr
AUDIO
COMPONENT
R
L
VIDEO
S-VIDEO
ANT
AUDIO
VIDEO1
HEAD PHONE
Audio Cable
Video Cassette
Recorder
Rear of this TV
ex.
(OUT)
(OUT)
(IN)
(IN)
(OUT)
Video Cable
S-Video Cable
(IN)
OR

INSTALLING THE BATTERIES

Install two AAAbatteries (supplied)
matching the polarity indicated inside
battery compartment of the remote con-
trol.
[BATTERY PRECAUTIONS]
•Be sure to follow the correct polarity as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
•Do not mix different types of batteries together (e.g. Alkaline and Carbon-Zinc) or old batteries
with fresh ones.
•If the device is not to be used for a long period of time, remove the batteries to prevent
damage or injury from possible battery leakage.
•Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.
PREPARATION FOR USE
2
13
OPERATIONS
VIDEO2 input
VIDEO1 input
Note:
●If some digits appear in the corner of the screen when the unit is turned on at the first time,
press [POWER]without unplugging the power cord.
Notes:
●The AUDIO L jackis for mono input. The sound is heard from both speakers. Use this jack for
connecting monaural audio equipment.
●The S-VIDEO jackis given priority over the VIDEO jack.
Notes:
●This TVcan accept 480p / 480i / simplified 1080i video signal.
●Simplified 1080 video signal differs to the original 1080i video signal because it is displayed
after converted into 480p signal.

REMOTE CONTROL AND TOPPANEL FUNCTION

123
456
789
0+100
MENU
o
n
p
m
MUTE SLEEP
DISPLAY
CH RET
INPUT
SELECT
POWER
CH
VOL
POWER button
To turn TV on/off
Channel number buttons
Press two digits to directly access the
desired channel. Remember to press
a "0" before a single digit channel.
CH KK/LLbuttons
To select channels and move
up/down through menu items
MENU button
To view on-screen menu SLEEPbutton
To set Sleep Timer
DISPLAY button
To display CH No./Audio Status
CHRET button
To return to previous channel
INPUTSELECT button
To select TV or external input
MUTE button
To mute sound
VOL XX/YYbuttons
To adjust volume
To decide the command of settings
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO
WIDE SLOT, FULLYINSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LALAME LA
PLUS LARGE DE LAFICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET
POUSSER JUSQU’AU FOND.
[EXTERNAL CONNECTION]
L
Y
Pb
Pr
R
L
VIDEO2
AUDIO
R
VIDEO1
S-VIDEO
VIDEO
HEAD PHONE
ANT
AUDIO
COMPONENT
ANT
IN
OUT
Note:
•Foryour safety and to avoid damages to the unit, unplug the antenna cable from the
ANTjack before moving the unit.

SELECTING AUDIO/VIDEO INPUT

When you use the AUDIO/VIDEO input jacks, select “VIDEO1” or“VIDEO2” mode by
pressing [INPUT SELECT]on the remote control or [INPUT SELECT] on the main unit.
The input mode changes by pressing the button as following:
TV channel VIDEO1 VIDEO2
INPUT
SELECT
Plug the incoming cable into the ANTjack on the rear of the TV.
*
NOTE (DO NOTDISCONNECT FROM BOX)
Some cable TVsystems use scrambled signals
and require a special converter to receive these
channels. Consult your local cable company.
Rear of this TV
OR
Incoming cable from home Antenna /
Cable Company (No Cable Box)
Incoming cable from Cable
Company or Satellite Antenna
Cable Box or
Satellite Box*
Cable
TVsignal Antenna
OR
IR transmitter
To send infrared ray (IR) signal
Note:
●You can test if the remote control sends out the infrared signal with an AM radio.
(Refer to “TROUBLESHOOTING GUIDE”.)

Tilt Stand

Adjust the stand to change the angle of TV(-5°~ 10°).
-5°10°

TILT STAND

CONNECTIONS

+100 button
Press to select cable channels
higher than 99.
Notes:
●In case no channel can be received by the channel scanning, “NO TVSIGNALS” is displayed on
the screen. Turn off the unit and check the antenna connection, then follow step 1 again.
●
If those settings do not work properly, please call our help line on the front page of this owner's manual.
2
2If the TVscreen shows
snow noise and there is
no operation for more
than 5 seconds,
“HELPFULHINTS”
appears. Follow the
instructions listed on-
screen.
Select the desired
language according to
the screen indication.
After that, the TV
performs “AUTO
PRESETCH” to scan
channels available for
the broadcasting in
your area.
SELECT LANGUAGE
ENGLISH NEXT:PRESS CHK
ESPAÑOL DESPUÉS:PRESIONE CHL
FRANÇAIS APRÈS:PRESSEZ VOLX
– INITIAL SETUP –
PLEASE CONNECT ANTENNA OR CABLE
OR SATELLITE TO THIS UNIT.
THEN PRESS CH K,
IN ORDER TO PERFORM
“AUTO PRESET CH ”.

INITIAL SETUP

When you turn on the power for the first time, the “SELECTLANGUAGE” menu is displayed.
The “INITIALSETUP” menu is displayed every time you turn on the unit unless the scanning is completed.
1
1- HELPFUL HINTS -
1.PLEASE CHECK TO SEE IF THE
ANTENNA/CABLE/SATELLITE IS
PROPERLY CONNECTED.
2.DID YOU PERFORM “AUTO PRESET CH” ?
3.PLEASE REFER TO FRONT PAGE OF THE
OWNER’S MANUAL OR REAR PANEL FOR
SUPPORT LINE INFORMATION.
When the scanning is completed, or [MENU]is pressed during channel scanning to cancel it, the
tuner stops on the lowest memorized channel.
POWER
MENU
VOLUME
CHANNEL
INPUT SELECT
POWER
MENU
VOLUME
CHANNEL
INPUT SELECT
POWER
POWER button
To turn TV on/off
VOLUME KK/LLbuttons
To adjust volume
INPUT SELECT button
To select TV or external input
CHANNEL KK/LLbuttons
To select channels
MENU button
To view on-screen menu
Infrared Sensor Window
Power Indicator