Emerson EWV404 owner manual Before using your VCR, HintHint, RF Output Channel, Printed in China

EMERSON AND THE G-CLEF LOGO ARE REGISTERED TRADEMARKS	RF Output Channel
OF EMERSON RADIO CORP., PARSIPPANY, NEW JERSEY, U.S.A.

Owner’s Manual	If you need additional operating assistance after
	reading this owner’s manual or to order replace-
Video Cassette Recorder	ment accessories, please call
	TOLL FREE : 1-800-256-2487
EWV404
	or visit our web site at http://www.funai-corp.com

1. Before using your VCR

If channel 3 is already occupied for broadcasting,

1)Set your TV to channel 4.

2)Insert a pre-recorded tape into the VCR.

3)Press the PLAY button once.

4)After a few seconds, press the PLAY button on the VCR for 3 seconds.

•The RF output channel will change to channel 4 from channel 3 and you will see a playback picture.

•When a picture does not appear on the TV screen, repeat step [4].

5) Press the STOP button to stop playback.

HintHint

•The RF output channel may not change when you adjust tracking during playback. In this case, stop the playback, and start the playback again. After that, press the PLAY but- ton on the VCR for 3 seconds again.

Basic VCR/TV Connection

Stereo TV Connection

Cable Antenna

Signal

or

(Back of TV)

Disconnect

Cable Antenna

Signal

or

2

Connect

(Back of VCR)

(Back of TV)

ANT
IN	3
OUT
	Connect

You can use the AUDIO OUT jack and VIDEO OUT jack on the back of the VCR if your TV has Audio/Video Input jacks. In this case, you need to set the TV to external Line Input Mode. Please refer to your TV’s owner’s manual.

VIDEO AUDIO IN
IN	L	R	ANT
			IN
		AUDIO
		OUT IN	OUT
		VIDEO

Audio/Video Cables

(not supplied)

1

	Connect
(Back of TV)	(Back of VCR)

RF Cable (supplied)

4 Plug the AC power cords of the VCR and TV into the AC outlets.

Hint for Cable Box or Satellite Box

Front & Rear Terminals

AUDIO OUT jack

Connect the audio cable to the audio in jack of a camcorder, another VCR, a stereo amplifier, or an audio system.

AUDIO IN jack

Connect the audio cable from the audio out jack of a camcorder, another VCR, or an audio source.

Connection A (Back of VCR)

(Cable	box or	ANT
Satellite box)
		IN
IN OUT		OUT	RF Cable	E
Cable
			(supplied)
Signal
				(Back of TV)

Select this connection when you want to view or record a scrambled channel. With this connection, channels cannot be changed on the VCR. You can view or record ONLY the channels you have selected on the cable box or the satellite box.

Connection B		(Back of VCR)
	ANT	(Cable	box or
	IN
Cable	OUT	Satellite box)
			E
Signal		IN OUT
	RF Cable (supplied)		RF Cable (Back of TV)

Select this connection when you want to change channels on the VCR. With this connection, you may watch one channel while recording another.

• You may not view or record a scrambled channel.

	ANT
	IN
AUDIO
OUT IN	OUT
VIDEO

VIDEO OUT jack

Connect the video cable to the video in jack of a camcorder, another VCR, or a TV.

POWER VCR/TV TAPE IN TIMER REC

AUDIO

OUT IN

VIDEO

ANT	ANT IN jack
IN
	Connect your antenna or cable box.
	ANT OUT jack
OUT	Connect the RF cable (supplied) to
	the antenna input jack on your TV.

VIDEO IN jack

Connect the video cable from the video out jack of a camcorder, another VCR, or an audio-visual source (laser disc player,

•While you are recording, only the recorded channel can be viewed.

To select channels of the cable box or satellite box

1)Turn on the VCR by pressing the POWER button, and then, press the VCR/TV button.The POWER and the VCR/TV indicators on the front panel will light on. Then, press the CHANNEL buttons to select channel 3 or 4 (the same channel as the output channel of the cable box or satellite box).

•If you use the channel 4, you need to change the VCR’s RF output to channel 4. Refer to “RF Output Channel”.

2)At the TV, select channel 3 or 4 (the same channel as you have selected at step 1).

3)At the cable box or satellite box, select the channel you

want to view or record.

To select channels of the cable box or satellite box		VIDEOAUDIO
		POWER	CHANNEL	MENU
1)At the cable box or satellite box, select channel 3 or 4
(the same channel as the VCR’s RF output channel.)
• Refer to “RF Output Channel”.		Supplied Accessory
2)At the TV, select the same channel as the output chan-
nel (3 or 4) of the cable box or satellite box.		• Remote control	• RF Cable	• Owner’s Manual
3)Turn on the VCR by pressing the POWER button, and
then, press the VCR/TV button .The POWER and		(NA372UD) with	(WPZ0901TM002)	(0VMN04033)
VCR/TV indicators on the front panel will light on. Then,		Two AA batteries
select the channel you want to view or record.
To play back a tape
Follow the steps 1) to 2) above. Then, play back a tape.
• Refer to “Playback” on page 5.
To view one channel while recording another
1)While you are recording on the VCR, press the VCR/TV but-
ton so that the VCR/TV indicator disappears on the VCR.
2)At the cable box or satellite box, select the channel you
want to view.	- 1 -

video disc player, etc.).

Installing the Batteries for the Remote Control

Install two AA batteries (supplied) matching the polarity indicated on

the bottom of the remote control.

Printed in China

0VMN04033 / HF331UD ★★★★★