Español Français English

These operations are accessible by remote control. Some may also be accessible by controls on the main unit.

INTRODUCTION

5Initial Setup

This section will guide you through the unit’s initial setting which includes selecting a language for your on-screen menu and autoscan, which automatically scans and memorizes viewable channels.

Before you begin:

Make sure the unit is connected to antenna or cable.

1 After making all the necessary connections, press [POWER] to turn on the unit.

4 Use [Cursor s/ B] to select the desired location setting, then press [ENTER].

InitialI i i l Setup

Select “Retail” or “Home” for your location.

Retail

Home

Select

ENTER Enter

PREPARATION

• This operation may take a few moments.

2 Use [Cursor K/L] to select the on-screen language from the choices on the right side of the TV screen. (English / Español / Français)

InitialI i i l Setup

 

 

 

 

 

 

Select the language for setup display.

 

English

 

Elija el idioma de ajuste.

 

 

Español

 

 

 

Français

 

Sélectionner langue écran config.

 

 

 

 

 

 

 

Select

ENTER Enter

SETUP

 

 

Skip

“Initial Setup” menu on step 3 will be displayed in the selected language after you press [ENTER].

3 Use [Cursor K/L] to select “Antenna” for TV channels or “Cable” for CATV channels, then press [ENTER].

InitialI i i l Setup

Make sure the antenna is connected to“ANT. IN” jack.

Antenna

Select the destination of “ANT. IN” jack.

 

 

Cable

 

 

 

 

 

 

Skip

Antenna

Or

 

 

Cable

 

ANT.IN

 

 

 

Select

ENTER Enter

BACK

SETUP

Back

Skip

• “Autoscan” will begin.

InitialI i i l Setup

Now the system is scanning for channels,please wait.

Autoscan will take up to 20 minutes to complete.

0%

Analog channels

0ch

 

 

 

 

 

 

 

 

Digital channels

0ch

 

 

 

 

 

 

SETUP

Skip

Select ”Retail”, the unit will be set up with predefined setting for retail displays. In this setting, the power consumption may possibly exceed the limited requirement of the ENERGY STAR® qualification.

Select ”Home”, the unit is set to maximize the energy efficiency for home setting and it can be adjusted through a choice of picture and sound quality according to your preference.

When the initial setup is completed, the lowest memorized channel with the confirmation message of the location setting will be displayed on the TV screen.

Note:

If you connect the cable system directly, contact the CATV installer.

If you press [POWER] or [SETUP] during autoscan, this setting will be canceled.

The initial autoscan function can be executed for either “Antenna” or “Cable” only once. When you change the connection (Antenna / Cable), set autoscan again.

Refer to page 18.

If there is no signal input from the antenna terminal and no operation for several seconds after you turn on the unit, “Helpful Hints” appears. Follow the instructions listed on the TV screen.

InitialI i i l Setup

 

 

 

 

 

No channel is registered.

 

 

 

Retry

Try Autoscan again?

 

 

 

Later

Verify that you have a cable connected to the " ANT. IN" jack

 

 

 

on the back of the TV, the channel installation process

 

 

 

searches this connection. If you are using a cable or satellite

 

 

 

box, please confirm the input which you have connected the

 

 

 

box and press the “INPUT SELECT” key on the remote control to

 

 

 

select the appropriate source input.

 

 

 

 

 

 

 

 

Select

ENTER Enter

SETUP

 

Skip

You must set ”Home” in step 4. Otherwise, the settings of picture and sound quality you adjusted will not be memorized after you turn off the unit.

After an initial setup is completed...

If you want to scan the channels automatically again, refer to “Autoscan” on page 18.

You can add the desired channels unmemorized by “Autoscan”. Refer to “Manual Register” on page 19.

If you want to change to another language, refer to “Language Selection” on page 20.

If you want to change the location setting, refer to “Location” on page 31.

WATCHING TV OPTIONAL SETTING TROUBLESHOOTING INFORMATION

13

EN

Page 13
Image 13
Emerson LC320EMXF owner manual Initial Setup, Before you begin, After an initial setup is completed, Autoscan will begin