![](/images/new-backgrounds/1043600/436003x1.webp)
Assembly and Installation
!WARNING
Do not install or use the fixture if any part is missing or damaged. Contact your dealer for replacement.
NOTE: For installation on Emerson fans with a center screw in modular (detachable) switch cup, proceed to step 1, page 2. For fans with center screw in switch housing cover, proceed to step 1, page 3.
Installation on Emerson Fans with a Center Screw and with Modular (Detachable) Switch Cups
1.Remove all parts and parts packages from the carton.
!WARNING
To avoid possible electrical shock, be sure electricity is turned off at the main fuse or circuit breaker box before wiring.
5.Carefully locate the white and blue wires (labeled either "L" or "LIGHT") in the switch cup and remove the wire connectors from the wires.
6.Insert the black and white wires from the light fitter(7) through the center hole in the switch cup (Figure 2) and thread the switch cup onto the light fitter. Hold wires taut while installing switch cup to prevent the wires from twisting. Securely tighten the fitter to the switch cup.
7.Insert the black and white wires through the lockwasher(7) and hex nut(8) supplied. Firmly tighten the hex nut to secure the light kit fitter to the switch cup.
8.Connect the white wire from the switch cup to the white wire of the light fitter (Figure 2). Connect the blue wire from the switch cup to the black wire of the light fitter. Use listed wire connectors (previously removed in step 5) to make connections (Figures 2 and 3).
!WARNING
To avoid possible fire or electrical shock, make certain no bare wire strands are exposed outside wire connectors.
Figure 3
!WARNING
To avoid possible fire or electric shock, be careful not to pinch wires between switch cup and the cover plate.
12.Proceed to “Installation of Glass Bowl” section.
Installation on Emerson Fans With Center Screw in Switch Housing Cover
(Not Modular Switch Cup)
1.Remove all parts and parts packages from carton.
(1) SWITCH HOUSING ASSEMBLY
| FAN SWITCH | |
| CHAIN | |
| (3) WIRE | |
BLUE WIRE | CONNECTORS | |
| ||
BLACK WIRE | WHITE WIRES | |
(5) COVER | (8) HEX NUT | |
(7) LOCKWASHER | ||
| ||
(2) SCREWS |
| |
(4) CENTER |
| |
SCREW |
| |
(6) LIGHT FITTER |
|
Figure 4
6.Connect the white wire from the ceiling fan to the white wire of the light kit fitter(6). Connect the blue wire from the ceiling fan to the black wire of the light kit fitter. Use listed wire connectors(3) (previously removed in step 3) to make connections. (Figures 4 and 5.)
!WARNING
2.Remove the switch cup(1) from the cover plate(2) by removing the three screws(3) around the side of the switch cup (Figure 1).
3.Disconnect the motor connector(4) from the switch cup connector(5) (Figure 1).
4.Remove the center screw(6) from the switch cup (Figure 1).
(4)MOTOR CONNECTOR
BLUE WIRE BLACK WIRE
(3) SCREWS
(9) HEX NUT
(8) LOCKWASHER
(1) SWITCH
CUP
(7)LIGHT FITTER
(2)COVER PLATE
(5)SWITCH CUP CONNECTOR
(6) WIRE CONNECTORS
WHITE WIRES
FAN SWITCH CHAIN
NOTE: YOUR FITTER MAY NOT LOOK THE SAME AS THE ONE IN THIS ILLUSTRATION. HOWEVER, IT INSTALLS IN A SIMILAR MANNER.
!WARNING
To avoid possible electric shock, be sure electricity is turned off at the main fuse or circuit breaker box before wiring.
2. Remove the cover from fan switch |
housing(1) by removing the two outer |
screws(2). (See Figure 4). |
3. Remove the center screw(4) in the |
switch housing cover(5). Insert the |
black and white wires from the light kit |
fitter(6) thru the hole and thread the |
To avoid possible fire or electrical shock, make certain no bare wire strands are exposed outside wire connectors.
Figure 5
7.Carefully tuck all wires and splices into the switch housing(1).
8.Attach the cover/light fitter(5)(6) to the switch assembly housing(1) using the two screws(2) that were removed in Step 2) (Figure 4.)
(4) MOTOR | (2) COVER PLATE |
| |
CONNECTOR |
|
(3) SCREWS | (5) SWITCH CUP |
CONNECTOR |
(1)SWITCH CUP
(6)CENTER SCREW
Figure 1
Figure 2
9.Carefully tuck all wires and splices into the switch cup(1). (Figure 2.)
10.Connect the motor connector(4) to the switch cup connector(5).
11.Position the cup/light fitter(1)(7) on the cover plate(2) and install the three screws(3) that were previously removed in step 2 and tighten securely.
switch housing cover tightly onto the |
light kit fitter. |
4. Insert the black and white wires through |
the lockwasher(7) and hex nut(8) |
supplied. Firmly tighten the hex nut to |
secure the light kit fitter to the switch |
cup. |
5. Carefully pull down the white and blue |
wires from the switch housing(1) and |
remove the wire connectors. |
!WARNING
To avoid fire or electrical shock, be careful not to pinch wires between the switch housing assembly and the cover.
9.Proceed to “Installation of Glass Bowl” section.
2 | 3 |