NOTE: This equipment has been tested and found to comply with part 18 of the FCC Rules. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment OFF and ON, the user is encouraged to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Replacement of the
Fluorescent Bulbs
1.Remove the pendants from the fan and light switch chains (Figure 7).
FLUORESCENT BULB
LIGHT FITTER
THREADED
NIPPLE
| (1) GLASS | |
| SHADE | |
LIGHT FITTER CHAIN | FAN SWITCH CHAIN | |
(4) GUIDE PLATE |
| |
HEX NUT |
| |
(3) GLASS CAP |
| |
(2) FINIAL NUT | FAN SWITCH | |
PENDANT | ||
| ||
LIGHT SWITCH |
| |
PENDANT/COUPLING |
|
Figure 7
2.Hold the glass shade(1) securely while removing the finial nut(2), glass cap(3), hex nut and the guide plate(4) (Figure 7).
3.Carefully place the glass shade, finial nut, glass cap, hex nut and guide plate in a safe place while replacing the bulb(s).
NOTE: Use only replacement
4.Install the replacement bulb in accordance with the “Installation of Fluorescent Bulbs and Glass Shade” section, on Page 5.
Installation on Emerson
Fans with Modular
(Detachable) Switch Cups
1.Remove all parts and parts packages from the carton.
2.On the ceiling fan, remove the switch cup(1) from the cover plate(2) by removing the three screws(3) around the side of the switch cup (Figure 1).
3.Disconnect the motor connector(4) from the switch cup connector(5) (Figure 1).
4.Remove the center screw(6) from the switch cup (Figure 1).
5.Carefully locate the white and blue wires (labeled either "L" or "LIGHT") in the switch cup. Remove and retain the wire connectors(6) from the wires (Figure 2).
6.Insert the black and white wires from the light fitter(7) through the center hole in the switch cup (Figure 2) and thread the switch cup tightly onto the light fitter. Hold wires taut while installing switch cup to prevent the wires from twisting.
(4) MOTOR | (2) COVER PLATE |
| |
CONNECTOR |
|
(3) SCREWS | (5) SWITCH CUP |
CONNECTOR |
(1)SWITCH CUP
(6)CENTER SCREW
Figure 1
7.Insert the black and white wires through the lockwasher(8) and hex nut(9) supplied. Firmly tighten the hex nut to secure the light kit fitter(7) to the switch cup(1) (Figure 2).
8.Connect the white wire from the switch cup to the white wire of the light fitter (Figure 2). Connect the blue wire from the switch cup to the black wire of the light fitter. Use U.L. listed wire connectors (previously removed in Step 5) to make connections (Figures 2 and 3).
(4) MOTOR | (2) COVER PLATE | |
(5) SWITCH CUP | ||
CONNECTOR | ||
CONNECTOR | ||
| ||
BLUE WIRE | (6) WIRE | |
CONNECTORS | ||
BLACK WIRE | WHITE WIRES | |
(3) SCREWS | ||
FAN SWITCH | ||
(9) HEX NUT | ||
CHAIN | ||
(8) LOCKWASHER | ||
|
(1)SWITCH CUP
(7) LIGHT FITTER
Figure 2
!WARNING
To avoid possible fire or electrical shock, make certain no bare wire strands are exposed outside wire connectors.
Figure 3
9.Carefully tuck all wires and splices into the switch cup(1). (Figure 2.)
10.Connect the motor connector(4) to the switch cup connector(5).
6 | 3 |