1.Assemble the wheels onto the wheel support frame as follows:
a.Install one of the cotter pins into the hole on one end of axle.
b.Slide the large washer, then wheel onto the axle next to the cotter pin.
c.Slide a small washer, spacer, small washer onto the axle next to the wheel.
d.Slide the partially assembled axle through the wheel support frame.
e.Slide the small washer, spacer, and small washer onto the axle next to the wheel support.
f.Slide the wheel then large washer onto the axle and hold in place with the remaining cotter pin.
g.Install the caps over the larger washers to finish the wheel assembly.
2.Position the heater on the wheel support frame assembly with the exit end over the wheels.
3.Use eight screws and nuts to attach the handles to the top of the tank flange. The screws will go through the handles, tank flange and wheel support frame. Install the nuts and finger tight only until all nuts are installed.
4.Tighten all the nuts.
5.Attach cord caddies to handles using No. (14) & No. (5) screws and nuts.
PREPARING FOR OPERATION
1.Check the heater for possible shipping damage. If any is found, immediately notify the factory.
2.Follow all of the "Precautions".
3.Fill the fuel tank with clean kerosene. In extremely cold weather, condensation may develop in the tank and it is recommended that a tablespoon of
IMPORTANT: Before filling fuel tank the first time or after extended storage periods, drain the fuel tank of any moisture or condensation.
4.Locate heater at a safe distance from combustible materials. ModelS 50K & 75KT is not suitable for use on wood floors or other combustible materials. When used, the heater should rest on suitable insulating material at least 1 inch thick and extending 3 ft. or more beyond the heater in all directions.
START
1.50K: Plug the heater into a grounded 115V, 60 Hz, 1 Ø outlet.
75KT, 125KT & 175KT: Turn thermostat to lowest setting, make sure “On/Off” switch is “Off”. Plug the heater into a grounded 115V, 60 Hz, 1 Ø outlet. Turn thermostat to highest setting. Start heater by push toggle switch to “On” position (light signifies switch is in “ON” position). Adjust thermostat to desired setting. Heater will cycle on/off as heat is required.
For all models: In cold weather, starting may be improved by holding a finger over the end of the pressure adjusting screw until the heater starts. This unit is equipped with a circuit breaker located near the power cord. If the unit does not start, check to see that the reset button is pressed in.
STOP
1.50K: Unplug heater from power source.
75KT, 125KT & 175KT: Push “On/Off” switch to “Off” position. For extended shutdown, unplug heater from power source.
RESTART AFTER SAFETY SHUTDOWN (50K, 75KT, 125KT
& 175KT)
1.Wait 5 minutes.
2.Press reset button.
Handle assembly for 125KT 175KT only.
ITEM | PART NO. | DESCRIPTION | QTY |
1 | M4365 | Handle, Front | 1 |
2 | M4338 | Handle, Rear | 1 |
3 | M4339 | Wheel Support Frame | 1 |
4 | M6977 | Machine Screw Blk (long) | 8 |
5 | M6037 | Kep Nut Blk | 12 |
6 | M8746 | Axle | 1 |
7 | M8752 | Wheel | 2 |
8 | M8751 | Cap | 2 |
9 | M8748 | Spacer | 2 |
10 | M8747 | Washer, Small | 4 |
11 | M8749 | Washer, Large | 2 |
12 | M8750 | Cotter Pin | 2 |
13 | M8754 | Ext. Cord Caddy | 2 |
14 | M7336 | Machine Screw Blk (Small) | 4 |
Enerco Group, Inc. Kerosene Forced Air Heater | 4 | Operating Instructions and Owner’s Manual |