For proper operation the chimney connector should be as short as possible and never exceed a six-foot (6’) horizontal run. Horizontal runs of chimney connector pipe should have an upward slope of one quarter of an inch (1/4”) per foot. You will need to maintain eighteen inches (18”) of clearance from the wall and ceiling unless you are using double wall or shielded pipe.

Hot Air Hook-Up

You are now ready to distribute air from the 8” outlet on the top of the stove into your existing duct system. Always install the add-on-furnace’s 8” diameter supply duct to the hot air trunk line of your existing hot air system, as close to the vent fan as possible. Thirty (30) gauge pipe or heavier should be used to make this connection; using the least possible amount of pipe will help the heat transfer to your duct system. Cut an eight-inch diameter hole in the main trunk line of the existing furnace duct, which is usually located on the top of the central furnace. Slide the eight-inch pipe from the add-on-furnace into the hole and seal the connection with duct tape. NOTE: Install a 8” 90 degree elbow inside this hole so that air flow from central furnace will not be directed back into the hot air pipe from the add-on furnace.

Thirty gauge or thicker black pipe should be used for the first two feet and then thirty gauge or thicker galvanized pipe can be used to connect to the existing furnace duct. Sheet metal screws should be used to secure each joint of pipe and an aluminum heat resistant tape can be wrapped around each joint to give an airtight seal.

The CA-18 blower can be installed by sliding the flange on the blower into the channel track located at the bottom and rear of the unit.

The AC-12 thermostat can be installed by plugging the 110 connection into the wall and the opposite end into the blower. The magnetic thermal disc should be attached to the rear wall of the stove in such a manner that the power cord does not come into contact with the stove. The thermostat will turn the blower on at approximately 140 degrees and shut the blower down at approximately 90 degrees. The frequency of the blower cycle will be affected by the placement of the thermostat on the rear of the unit. Mounting the thermostat closer to the blower will allow the blower to come on less frequently. We recommend the thermostat be placed in the center of the rear wall as a starting point.

SECTION IV: OPERATING INSTRUCTIONS

A. Building a Fire

CAUTION: NEVER USE KEROSENE, GASOLINE, DIESEL FUEL OR CHARCOAL LIGHTER FLUID TO LIGHT OR RE-KINDLE A FIRE.

NOTICE: Your new unit and the connector pipe may smoke for a short period of time. This is called “cooking out” and is no cause for alarm. It is a good idea to open all doors and windows in your dwelling during the first few hours of operation.

1.Place several wads of crushed paper over the entire bottom of the stove.

2.Place small dry sticks (kindling) of wood on the paper.

3.Be absolutely sure there are no combustibles in the immediate area of the stove.

4.Open the two cast iron dampers on the door by turning them counterclockwise.

5.Ignite the paper and leave the door cracked open until the fire is burning freely.

6.Once the kindling is burning freely, add several pieces of split dry wood to the fire. Allow this wood to start burning well before closing the door completely.

7.Close the door and adjust the cast iron dampers on the door by turning them clockwise.

Page 4 Page 6
Page 5
Image 5
England's Stove Works 24-G operation manual Section IV Operating Instructions, Hot Air Hook-Up, Building a Fire
Page 4 Page 6

24-G specifications

England's Stove Works 24-G is an impressive wood-burning stove that successfully combines traditional craftsmanship with innovative technology. This stove is designed to provide efficient heating, making it an attractive option for homeowners seeking a reliable source of warmth while also enjoying the aesthetic appeal of a classic wood stove.

One of the main features of the 24-G is its impressive heating capacity. With the ability to generate up to 75,000 BTUs, this stove is capable of heating spaces of up to 1,800 square feet, making it suitable for a variety of home layouts. Its large firebox can accommodate logs up to 24 inches long, allowing for longer burn times and reduced need for frequent refueling.

Another significant aspect of the England’s Stove Works 24-G is its advanced air wash technology. This feature helps keep the glass door clean, enhancing the visual appeal of the fire while maximizing the viewing experience. The air wash system effectively reduces soot build-up, allowing users to enjoy a clear and unobstructed view of the flames.

The construction of the 24-G is another noteworthy feature, as it is built from heavy-duty steel. This ensures durability and longevity, making it a sensible investment for any home. The stove also boasts a cast iron door that not only adds to its traditional design but also enhances its heat retention capabilities.

In terms of efficiency, the 24-G excels with an overall efficiency rating of up to 78%. This efficiency translates into less wood consumption while still providing substantial heating. Such characteristics contribute to lower heating costs and a more environmentally-friendly option for homeowners.

The stove is also designed with a variety of adjustable air controls, allowing for precise regulation of combustion and heat output. This flexibility enables users to customize the heating experience according to their specific needs and preferences.

Overall, England’s Stove Works 24-G represents a perfect fusion of style, efficiency, and performance. Its robust design, advanced technologies, and heating capabilities make it an ideal choice for anyone looking to enhance their home with a reliable and beautiful wood-burning stove. Whether it’s for cozy family gatherings or simply enjoying the warmth during a cold winter evening, the 24-G stands out as a top contender in the market.
Top Page Image Contents