Operating Instructions

OPERATING YOUR PELLET STOVE:

PRE-BURN INSTRUCTIONS: The burn pot liner holes must be clear and the liner installed properly against the ignitor tube for proper operation. Check the hopper for enough pellets to start the unit.

DO NOT OPERATE THE UNIT WITH THE DOOR OR ASH PAN OPEN.

MANUAL MODE:

To START: Press the ON / OFF button. The stove will turn on. The system light will flash. The Auger Light will flash with each pulse of the auger (the Auger Feed Rate is pre-programmed during start-up). The Heat Level Indicator will show the Heat Level that the stove will run at after start-up.

If this is the first time the unit has been started or the unit has run out of fuel, the auger will need to be primed. Press the Manual Auger Feed button until fuel starts to drop into the Burn Pot Liner (see

“OPERATING INSTRUCTIONS; STOVE CONTROLS”).

To OPERATE: When a fire has been established, the System Light will turn solid (after approximately 10

-15 minutes) and the Auger Light will continue to flash to the corresponding Heat Level setting. The Heat Level button can now be pressed at this time to change the desired Heat Level Output setting.

The convection blower (room air blower) will turn on. The speed of this blower is controlled by the setting of the heat level output indicator. The convection blower can be turned OFF by depressing the convection blower control button. For the best efficiency and to prevent cycling, the convection blower should be left on at all times.

When operating on LOW HEAT LEVEL, the feed rate can be adjusted, using the auger trim, for different quality fuels. These settings can be used if the fire keeps going out on low (poor quality fuel). Or if the

low setting is too hot for the room (see “OPERATING INSTRUCTIONS; CONTROL BOARD FUNCTIONS”).

THERMOSTAT / SWITCH MODE:

INITIAL START-UP: See above

OPERATION - HI / LOW mode: When the thermostat contacts are closed the stove settings are adjustable as per Manual Mode (see above). When the thermostat contacts open, the circuit board will take control of the settings. The stove will drop down to a low burn until the thermostat contacts close

again. This low burn setting can be adjusted for different fuel qualities (see “OPERATING INSTRUCTIONS;

STOVE CONTROLS - CIRCUIT BOARD”). The stove will come back to the previous HEAT LEVEL setting when the thermostat contacts close again.

OPERATION – ON / OFF mode: When the thermostat contacts close, the unit will light automatically. Once up to temperature, the stove operates the same as in manual mode (see above). When the thermostat contacts open, the unit automatically begins its shutdown routine. The stove will re-light when the thermostat contacts close again.

TURNING YOUR PELLET STOVE OFF:

•MANUAL and HI / LOW mode: To turn the unit OFF, simply press the ON / OFF button. This will stop the feed of pellets. The blowers will continue to operate and cool the stove down. When cool enough, the stove will turn off.

•ON / OFF mode: To turn the unit OFF, turn the thermostat down or off.

DO NOT unplug unit while Combustion fan is operating.

This may lead to smoke escaping from the stove.

8

Page 7 Page 9
Page 8
Image 8
Enviro C-10629 owner manual Thermostat / Switch Mode, Initial START-UP See above
Page 7 Page 9

C-10629 specifications

Enviro C-10629 is an innovative product designed for effective environmental management and sustainability solutions. This versatile formulation is particularly well-regarded for its ability to combat a wide range of environmental challenges, making it an essential tool for various industries, including agriculture, waste management, and soil remediation.

One of the main features of Enviro C-10629 is its biodegradable nature, which aligns with modern ecological practices. This characteristic not only helps minimize environmental impact but also ensures that the product can be safely used in sensitive ecosystems without leaving harmful residues. The formulation is designed to break down into non-toxic by-products, thereby contributing to a circular economy.

The technology behind Enviro C-10629 is based on advanced microbial and enzymatic activity. This allows the product to work in synergy with the natural processes found in soil and water environments. By harnessing the power of beneficial microorganisms, Enviro C-10629 enhances nutrient availability and improves soil health, facilitating robust plant growth and crop yields.

In terms of characteristics, Enviro C-10629 exhibits excellent compatibility with other agricultural inputs, which allows it to be easily integrated into existing practices. This compatibility ensures that farmers and land managers can use it in conjunction with fertilizers and other soil amendments without any adverse reactions. As a result, individuals can maximize the effectiveness of their agricultural inputs while promoting environmental sustainability.

Furthermore, Enviro C-10629 is designed to be user-friendly and requires minimal application effort. With an effective delivery system, it can be applied through various methods, including spraying, drenching, or mixing with irrigation systems. This ease of use ensures that users can implement the product without extensive training or specialized equipment.

Overall, Enviro C-10629 stands out as a cutting-edge solution for environmental challenges. Its biodegradable composition, advanced microbial technology, compatibility with other agricultural practices, and user-friendly application methods make it an essential product for those seeking to promote sustainability while maintaining productivity. As industries increasingly prioritize eco-friendly solutions, Enviro C-10629 represents a significant step forward in achieving these goals.
Top Page Image Contents