Maintenance and Service

3.Vacuum the bottom of the firebox thoroughly. Carefully clean off any dust on the logs and remove any lint from the main burner and pilot burner.

4.After carefully replacing the log and embers in their correct positions (see Secondary Installation - Installation of Log Set and Embers), and the door has been resealed, re-light the pilot, following the instructions on the lighting label attached to the unit.

CLEANING PLATED SURFACES:

It is important to note that fingerprints and other marks can leave a permanent stain on plated finishes. To avoid this, give the face a quick wipe with denatured alcohol on a soft cloth BEFORE lighting the fireplace. Never clean the face when it is not cool. Do not use other cleaners as they may leave a residue, which can become permanently etched into the surface.

BURNER REMOVAL:

The burner may need to be removed for a few reasons, including cleaning under the burner, converting the unit to a different gas type, or to replace the burner altogether. Proceed only when the unit has completely cooled down.

1.Remove the door as shown in the MAINTENANCE AND SERVICE - OPENING THE DOOR.

2.Remove the two (2) T-20 screws that hold

the burner in place; one (1) at each of the rear burner (see Figure 7).

3. Lift the burner assembly (both the front and rear burners) straight up then out.

To re-install the burner follow steps 1-3 in

 

reverse. When placing the burner back in the

 

unit ensure that the venturi box under the

Figure 7: Screws holding Burner.

burner is lined up.

REPLACING THE BLOWER:

 

1.

Turn the unit off, allow it to cool down completely, and

 

remove the door as shown in the MAINTENANCE AND SERVICE

 

- OPENING THE DOOR..

2. Remove the log set and brick liner.

3.

Remove the burner tray assembly, see MAINTENANCE AND

 

SERVICE - BURNER REMOVAL.

4.

Remove the four (4) 5/16” bolts that hold the blower

 

mounting plate to the back firewall. Use a light lubricating

 

oil on screws before removal.

5.

Carefully pull the blower assembly into the firebox (see

 

Figure 7) disconnect the blower leads from the harness and

 

remove blower.

6.

To re-install, check mounting plate gasket if damaged

 

replace with new one and reverse steps 1 through 4. Refer

Figure 8: Blower (Fan) Removal.

to “SECONDARY INSTALLATION - LOG SET AND EMBERS INSTALLATION”.

9

Page 9
Image 9
Enviro EG40-070 owner manual Burner is lined up

EG40-070 specifications

The Enviro EG40-070 is a state-of-the-art outdoor wood-burning furnace designed to provide an efficient and eco-friendly heating solution for residential and commercial spaces. As homeowners increasingly seek sustainable alternatives to traditional heating methods, the EG40-070 emerges as a formidable contender in the market.

One of the standout features of the Enviro EG40-070 is its high-efficiency heating capability. With an impressive thermal efficiency rating, this furnace ensures that a significant portion of the heat generated from the burning wood is effectively transferred to the water that circulates throughout the heating system. This efficiency reduces the amount of wood needed for heating, making it an environmentally friendly option.

The furnace is equipped with a robust and durable construction, designed to withstand the rigors of outdoor use. The heavy-duty steel body is resistant to corrosion and wear, ensuring longevity and minimal maintenance. Additionally, the large firebox allows for extended burn times, which means users can load it with wood and enjoy consistent heating for hours without the need for constant refueling.

Another significant characteristic of the Enviro EG40-070 is its advanced combustion technology. It features a secondary combustion system that maximizes the efficiency of the fuel being burned. By allowing for the recirculation of exhaust gases, this system ensures that virtually all the combustible materials are utilized, resulting in cleaner emissions. This not only benefits the environment but also contributes to better air quality.

The Enviro EG40-070 also boasts a user-friendly design, complete with easy-access doors for loading fuel and cleaning. The integrated digital control system allows for precise regulation of the temperature and heat output, providing users with a customizable heating experience. Furthermore, the unit is compatible with various heating systems, including forced air and hydronic systems, making it versatile for different applications.

For safety, the furnace incorporates several safety features, including low water protection and an automatic shut-off function. These features are crucial in preventing overheating and ensuring safe operation, giving homeowners peace of mind.

In summary, the Enviro EG40-070 is a powerful outdoor wood-burning furnace that combines efficiency, durability, and functionality. Its advanced combustion technologies and user-friendly design make it a suitable choice for those looking to embrace a sustainable heating solution without compromising on performance or safety.