Safety Warnings & Recommendations

ELECTRICAL: The use of a surge protected power bar is recommended. The unit must be grounded. The grounded electrical cord should be connected to a standard 110-120 volts (4.2 Amps), 60 hertz electrical outlet and also must be accessible. If this power cord should become damaged, a replacement power cord must be purchased from the manufacturer or a qualified Enviro dealer. Be careful that the electrical cord is not trapped under the appliance and that it is clear of any hot surfaces or sharp edges. This unit’s maximum power requirement is 504 watts.

When installing the stove in a mobile home, it must be electrically grounded to the steel chassis of the home and bolted to the floor.

GLASS: Do not abuse the glass by striking or slamming the door. Do not attempt to operate the stove with broken glass. The stove uses ceramic glass. Replacement glass must be purchased from an Enviro dealer. Do not attempt to open the door and clean the glass while the unit is in operation or if glass is hot. To clean the glass, use a soft cotton cloth and mild window cleaner, gas or wood stove glass cleaner, or take a damp paper towel and dip into the fly ash. This is a very mild abrasive and will not damage the glass.

KEEP ASH PAN FREE OF RAW FUEL. DO NOT PLACE UNBURNED OR NEW PELLET FUEL IN ASH PAN. A fire in the ash pan may occur.

INSTALLATION: Contact your local building or fire official to obtain a permit and any information on installation restrictions and inspection requirements for your area.

Be sure to maintain the structural integrity of your home when passing a vent through walls, ceilings, or roofs, and all construction meets local building codes. It is recommended that the unit be secured into its position in order to avoid any displacement. This appliance must be installed on a floor with an adequate load bearing capacity, if existing construction doesn’t meet load capacity, suitable measures (e.g. load distributing plate) must be taken to achieve it.

DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST VENTING SYSTEM OF THIS UNIT. DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.

FRESH AIR: This unit uses large quantities of air for combustion; outside Fresh Air connection is strongly recommended. Fresh Air must be connected to all units installed in Mobile and “Air Tight Homes” (R2000) or where required by local codes.

Consider all large air moving devices when installing your unit and provide room air accordingly. NOTE: Extractor fans when operating in the same room or space as the appliance may cause problems. Limited air for combustion may result in poor performance, smoking and other side effects of poor combustion.

The stove’s exhaust system works with negative combustion chamber pressure and a slightly positive chimney pressure. It is very important to ensure that the exhaust system be sealed and airtight. The ash pan and viewing door must be locked securely for proper and safe operation of the pellet stove.

Do not burn with insufficient combustion air. A periodic check is recommended to ensure proper combustion air is admitted to the combustion chamber. Setting the proper combustion air is achieved by adjusting the slider damper located on the left side of the stove.

Soot or creosote may accumulate when the stove is operated under incorrect conditions such as an rich burn (black tipped, lazy orange flames).

If you have any questions with regards to your stove or the above-mentioned information, please feel free to contact your local dealer for further clarification and comments.

SINCE SHERWOOD INDUSTRIES LTD. HAS NO CONTROL OVER THE INSTALLATION OF YOUR STOVE, SHERWOOD INDUSTRIES LTD. GRANTS NO WARRANTY IMPLIED OR STATED FOR THE INSTALLATION OR MAINTENANCE OF YOUR STOVE. THEREFORE, SHERWOOD INDUSTRIES LTD. ASSUMES NO RESPONSIBILITY FOR ANY CONSEQUENTIAL DAMAGE(S).

SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE.

5

Page 4 Page 6
Page 5
Image 5
Enviro C-11407, Omega, 50-1675, C-11256 owner manual Safety Warnings & Recommendations
Page 4 Page 6

50-1675, C-11256, Omega, C-11407 specifications

Enviro C-11407, Omega, and C-11256, 50-1675 are cutting-edge technologies designed to address various environmental challenges through innovative engineering and advanced features. These systems have been developed for a wide range of applications, including waste management, air quality improvement, and resource conservation.

Enviro C-11407, known for its robust design, focuses on waste reduction and recycling processes. This system incorporates a modular architecture that allows for easy integration into existing waste management facilities. With its high-efficiency sorting capability, the C-11407 employs advanced sensors and machine learning algorithms to identify recyclable materials. The system can significantly increase the recovery rates of recyclable materials while reducing operational costs.

Omega technology, on the other hand, is geared towards air quality enhancement. This system utilizes sophisticated filtration and purification methods to remove pollutants from the atmosphere. The Omega unit employs a multi-stage filtration process, which includes HEPA filters, activated carbon, and photocatalytic oxidation, ensuring the highest level of air purification. Its smart monitoring system provides real-time data on air quality, allowing for proactive measures to be taken against pollution spikes, thereby improving public health and environmental conditions.

C-11256 is an advanced energy management system aiming to improve energy efficiency and reduce carbon footprints. This technology integrates renewable energy sources such as solar and wind with smart grid capabilities. The C-11256 utilizes energy storage systems that can store excess energy for use during peak demand times. Its predictive analytics feature allows users to optimize energy consumption, contributing to substantial cost savings and a decrease in greenhouse gas emissions.

The 50-1675 model represents a versatile solution for water treatment applications. This system features advanced membrane filtration technology capable of removing contaminants at the molecular level. With a focus on sustainability, the 50-1675 is designed to minimize water wastage while maximizing contaminant removal efficiency. Its compact design makes it suitable for various settings, including industrial processes, municipal water treatment, and even portable applications for remote areas.

Together, these technologies—Enviro C-11407, Omega, C-11256, and 50-1675—highlight a commitment to innovation in environmental management. By harnessing cutting-edge engineering and advanced analytical tools, they promote sustainability, enhance resource recovery, and improve overall quality of life for communities worldwide.
Top Page Image Contents