EPSON Stylus Pro 10600

 

 

 

Error messages (continued)

 

 

 

 

 

 

Message

Light

Explanation

Response

 

 

 

 

RELOAD PAPER

Paper Out light on

Paper could not be reversed into

Remove the paper. Reload it so that the bottom edge is straight

 

 

the printing position.

and aligned with the vertical row of holes at the paper exit.

 

 

 

 

 

 

Image is too wide for the paper

Resize your image or load wider paper.

 

 

loaded in the printer.

 

 

 

 

 

 

 

Paper is not fully ejected.

Cut the paper at the paper insertion slot, then reload paper.

 

 

 

 

 

 

PAPER NOT CUT error was

Reload paper.

 

 

cleared.

 

 

 

 

 

UNABLE TO PRINT

—

You tried to print while an error

After 3 seconds the message disappears. Press the Pause button

 

 

condition was present or the ink

to exit SelecType mode. If the message appears again, clear the

 

 

compartment cover was open.

error before you print.

 

 

 

 

NOZZLE CHECK ERROR

—

The nozzle check pattern did not

Press and hold the Cleaning button on the control panel for at

 

 

print correctly.

least 3 seconds to begin cleaning the print head.

 

 

 

 

COMMAND ERROR

—

You’re using the wrong printer

Make sure you installed the correct driver for your printer:

 

 

driver.

Stylus Pro 10600DYE driver for Photographic Dye

 

 

 

 

 

 

Stylus Pro 106000CF driver for Archival ink

 

 

 

Stylus Pro 10600UC driver for UltraChrome ink

 

 

 

 

 

 

Damaged data was sent to the

To clear the data, press the printer’s Power button to turn the

 

 

printer.

printer off. Wait for about a minute, then turn the printer on again.

 

 

 

 

MAINTENANCE REQ.

—

A printer part will need to be

Note the error number and contact EPSON.

 

 

replaced soon.

 

 

 

 

 

MAINTENANCE REQ

—

The waste ink system is almost

Call an authorized EPSON servicer to schedule replacement of

0100

 

full.

the waste ink system.

 

 

 

 

SERVICE REQ.

All lights flashing

An error has occurred.

Note the error number, and turn the printer off and then on. If the

 

 

 

message remains, contact EPSON.

 

 

 

 

SERVICE REQ. 00000100

All lights flashing

The waste ink system is full.

Contact EPSON to have the waste ink system replaced.

 

 

 

 

Printing a Status Check

The status check shows the amount of ink remaining in each cartridge, the page count, and the status of various printer parts.

NOTE: The user can replace the ink cartridges and cutter blade. Other parts need to be replaced by an authorized EPSON service technician.

Follow these steps to print the status check:

1.Load a sheet of letter-size paper in the printer. (You can print on roll paper, but you will use more paper.)

2.Press the SelecType button on the control panel until you see TEST PRINT MENU on the display.

3.Press the Item button until your see STATUS CHECK=PRINT.

4.Press the Enter button. The status check sheet prints.

The amount of ink left or the component life is indicated as follows:

E*****F = full (or full life remaining)

E**** F = 3/4 full (or 3/4 life remaining)

E***

F = 1/2 full (or 1/2 life remaining)

E**

F = 1/4 full (or 1/4 life remaining)

E*

F = nearly empty (or service life near end)

E F = empty (or service life ended)

5.Press the SelecType button to exit the Test Print menu.

9/02

EPSON Stylus Pro 10600 - 9