EPSON Stylus Pro 7000 series
Message/Light | Explanation | Response | |
|
|
| |
PAPER NOT | Paper slipped and fed | Reload paper, making | |
STRAIGHT/ | into the printer at an | sure the edges are | |
Paper Out light | angle. | straight and aligned with | |
flashing |
| both rows of holes. | |
|
|
| |
PAPER OUT/ | No paper is loaded. | Load paper. | |
Paper Out light |
|
| |
Paper ran out. | Remove any printouts or | ||
on | |||
| paper remaining in the | ||
|
| ||
|
| printer and load more | |
|
| paper. | |
|
| If the message appears | |
|
| during a print job, reset | |
|
| the printer by pressing | |
|
| the Pause button for 3 | |
|
| seconds. Then load | |
|
| paper and resend the | |
|
| job. | |
|
|
| |
RELOAD PAPER/ | Paper could not be | Remove the paper. | |
Paper Out light | reversed into the | Reload it so that the | |
on | printing position. | right and bottom edges | |
|
| are straight and aligned | |
|
| with both rows of holes. | |
|
|
| |
| Image is too wide for | Resize your image or | |
| the paper loaded in the | load wider paper. | |
| printer. |
| |
|
|
| |
| Paper is not fully | Cut the paper at the | |
| ejected. | paper insertion slot, then | |
|
| reload paper. | |
|
|
| |
| PAPER NOT CUT error | Reload paper. | |
| was cleared. |
| |
|
|
| |
REMOVE PAPER/ | Paper is too thick for | Push the paper set lever | |
Paper Out light | print head cleaning. | down to remove the | |
on |
| paper. Print head | |
|
| cleaning automatically | |
|
| starts. After cleaning, | |
|
| reload paper. | |
|
|
| |
SECURE PAPER | Paper set lever was | Pull the paper set lever | |
LEVER/Paper Out | released. | all the way up. Restart | |
light on |
| print job for best results. | |
|
|
| |
SERVICE REQ. | An error has occurred. | Note the error number, | |
<error number>/ |
| and turn the printer off | |
All lights flashing |
| and then on. If the | |
|
| message remains, | |
|
| contact EPSON. | |
|
|
| |
SERVICE REQ. | The waste ink system is | Contact EPSON for | |
00000100/ | full. | service. | |
All lights flashing |
|
| |
|
|
| |
TURN PWR OFF | This message appears | Turn the printer off and | |
AND ON | after you clear a paper | then on again. | |
| jam. |
| |
|
|
| |
UNABLE TO | You tried to print a test | After 3 seconds, the | |
pattern while an error | message disappears. | ||
| condition was present. | Press the Pause button | |
|
| to exit SelecType mode. | |
|
| If the message appears | |
|
| again, clear the error | |
|
| before you print. | |
|
|
|
SelecType Menu Map
The following illustration shows the SelecType™ menus, along with the settings available for each one.
PRINTER SETTING |
| TEST PRINT MENU: | PRINTER STATUS | ||||
| MENU: | ||||||
MENU: |
|
| |||||
|
|
|
| ||||
|
|
|
|
| NOZZLE CHECK | VERSION | |
PLATEN GAP |
| STATUS CHECK | |||||
PAGE LINE |
|
| INK | ||||
INTERFACE |
|
| INK | ||||
PARA. I/F |
|
| INK | ||||
CODE PAGE |
|
| INK | ||||
PAPER SIZE CHECK |
|
|
|
| INK | ||
PAPER ALIGN CHK |
|
|
|
| INK | ||
ROLL MARG |
|
|
|
| CUTTER LIFE | ||
INIT. PANEL |
|
|
|
| TOTAL PRINTS | ||
|
|
|
|
|
| WASTE INK | |
|
|
|
|
|
| ||
|
|
|
|
|
| CR MOTOR | |
|
|
|
|
|
| PF MOTOR | |
|
|
|
|
|
| HEAD UNIT | |
|
|
|
|
|
| CLEANER | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
READY |
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| |
HEAD ALIGNMENT |
| CUTTER REPLACE | PAPER CONFIG. | ||||
MENU: |
| MENU: | MENU: | ||||
PAPER THICK. |
| CUT. REPLACE | PAPER NUMBER | ||||
ADJUST. PATT. |
| OPEN LOWER COVER | THICK. PAT. | ||||
#1 |
|
|
| REPLACE CUTTER | PAPER THICK. NO. | ||
#2 |
|
|
| CLOSE LOWER COVER | SUCTION | ||
#3 |
|
|
|
|
|
| |
#4 |
|
|
|
|
|
| |
#5 |
|
|
|
|
|
| |
#6 |
|
|
|
|
|
| |
|
|
|
| ||||
#7 |
|
|
|
|
|
| |
#8 |
|
|
|
|
|
| |
#9 |
|
|
|
|
|
| |
#10 |
|
|
|
|
|
| |
#11 |
|
|
|
|
|
| |
#12 |
|
|
|
|
|
|
Printing a Status Check
The status check shows the current default settings, amount of ink remaining in each cartridge, page count, and the status of various printer parts.
Follow these steps to print the status check:
1.Load a sheet of paper in the printer. (You can print test pages on roll paper, but you will use more paper.)
2.Press the SelecType button on the control panel. Press it repeatedly until you see TEST PRINT MENU on the display.
3.Press the Item button until you see STATUS CHECK=PRINT on the display.
8/00 | EPSON Stylus Pro 7000 series - 7 |