Epson EMP-822H ft Power indicator lights red

Problem Solving 39

ft Power indicator lights red

: Lit : Flashing: : Off

Status Cause Remedy or Status

Internal Error Stop using the projector, disconnect the power cable from the electrical outlet, and contact your local dealer or the nearest

address provided in the Support and Service Guide. sEpson Projector Contact List

Fan Error

Sensor Error

Stop using the projector, disconnect the power cable from the electrical outlet, and contact your local dealer or the nearest

address provided in the Support and Service Guide. sEpson Projector Contact List

High Temp Error

(overheating)

The lamp turns off automatically and projection stops. Wait for about five minutes. After about five minutes the projector

switches to standby mode, so check the following two points.

• Check that the air filter and air exhaust vent are clear, and that the projector is not positioned against a wall.

• If the air filter is clogged, clean or replace it. sp.50, 56

If the error continues after checking the points above, stop using the projector, disconnect the power cable from the

electrical outlet, and contact your local dealer or the nearest address provided in the Support and Service Guide. sEpson

Projector Contact List

When using at an altitude of 1500 m or more, set "High Altitude Mode" to "On". sp.30

Lamp Error

Lamp Failure

Lamp Cover Open

Check the following two points.

• Take out the lamp and check if it is cracked. sp.53

• Clean the air filter. sp.50

If it is not cracked - Re-fit the lamp and turn on the power.

If the error continues - Replace the lamp with a new lamp and turn on the power.

If the error continues - Stop using the projector, disconnect the power cable from the electrical outlet, and contact

your local dealer or the nearest address provided in the Support and Service Guide.

sEpson Projector Contact List

If it is cracked - Replace it with a new lamp, or contact your local dealer for further advice. If replacing the lamp

yourself, be careful to avoid pieces of broken glass (you cannot continue projecting until the lamp is replaced). sEpson

Projector Contact List

Check that the lamp cover and the lamp are securely installed. sp.53

If the lamp cover or the lamp is not securely installed, the lamp does not switch on.

When using at an altitude of 1500 m or more, set "High Altitude Mode" to "On". sp.30

Problem

Red

Red

Red

Red

Red

Red

Red

Red

Red

Contents

Main Notations Used in This Guide fSafety Indications g fGeneral Information Indications q s Contents Useful Functions Configuration Menu Troubleshooting Appendices Projector Features Part Names and Functions Page Page Page Page Page Page Useful Functions Changing the Projected Image (Source Search) q Functions for Enhancing Projection Selecting the Projection Quality (Selecting Color Mode) p.24, 25 q the "Image" menu in the configuration menu. Hiding the Image and Sound Temporarily (A/V Mute) q Freezing the Image (Freeze) q Changing the Aspect Ratio (Aspect) Enlarging Part of the Image (E-Zoom) A B q Security Functions Managing Users (Password Protect) fType of Password Protect fSetting Password Protect q A seconds. B C A "Operation Lock" in the configuration menu. s"Using the Configuration Menu" p.23 B C q displayed. Anti-Theft Lock fInstalling the wire lock Configuration Menu Page List of Functions Image Menu (EMP-83H/822H Only) Image Menu (EMP-X5/S5 Only) Signal Menu (EMP-83H/822H Only) Signal Menu (EMP-X5/S5 Only) List of Functions 28 Settings Menu For EMP-83H/822H For EMP-S5For EMP-X5 List of Functions 29 Extended Menu For EMP-83H/822H For EMP-X5/S5 For EMP-X5/S5 (Euro) Page List of Functions 31 Network Menu (EMP-83H/822H Only) Page Page Info Menu (Display Only) List of Functions 35 Reset Menu For EMP-83H/822H For EMP-X5/S5 Troubleshooting Using the Help A p.38). s q "Problem Solving" ( Problem Solving Reading the Indicators Problem Solving 39 ft Power indicator lights red : Lit : Flashing: : Off fi o Indicator is lit or flashing orange q When the Indicators Provide No Help Problems relating to images Problems when projection starts Other problems Problem Solving 42 fProblems relating to images f Problem Solving 43 f f Problem Solving 44 f f Problem Solving 45 f f Problem Solving 46 fProblems when projection starts f fOther problems Problem Solving 47 f f Appendices Installation Methods q Warni ng Cleaning q Cleaning the Projector's Surface Cleaning the Lens Cleaning the Air Filter and Air Intake Vent Replacing Consumables A B Caution C Replacing the Lamp fLamp replacement period A B Warni ng Caution Page F q fResetting the lamp operating time Replacing the Air Filter q A B C Saving a User's Logo A B C q Screen Size and Distance EMP-83H/822H/X5 EMP-S5 Connecting to External Equipment q Connecting to an External Monitor q Connecting to External Speakers (EMP-83H/822H Only) Connecting a LAN Cable (EMP-83H/822H Only) To prevent malfunctions, use a category 5 shielded LAN cable. Page Optional Accessories and Consumables fOptional accessories fConsumables Glossary Glossary 66 ESC/VP21 Commands Command List Cable Layouts fSerial connection (EMP-83H/822H Only) Connecting a USB (EMP-X5/S5 Only) A B C PJLink (EMP-83H/822H Only) List of Supported Monitor Displays Specifications Page Page Page Appearance The external dimensions for EMP-83H/822H/X5/S5 are the same. Index A B C D P R S T U