Manuals / Brands / Home Audio / Home Theater System / Ericsson / Home Audio / Home Theater System

Ericsson RX8310, RX8330, RX8315 2.5Connecting the Receiver to the Power Supply, Note:, Power Supply, Fuse Type and Rating

1 40

Download 40 pages, 1.41 Mb

Installing the Equipment

2.5Connecting the Receiver to the Power Supply

Warning!

Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

As no mains switch is fitted to this unit, ensure the local power supply is switched OFF before connecting the supply cord.

The receiver is not fitted with an on/off switch. Ensure that the socket-outlet is installed near the equipment so that it is easily accessible. Failure to isolate the equipment properly may cause a safety hazard.

Connect the receiver to the power supply as follows:

1.Ensure the power supply is isolated and switched off.

2.Ensure the correct fuse type and rating has been fitted to both the equipment and the power cable.

3.Connect the lead to the receiver input connector and then to the power supply.

4.Switch on the power supply.

Table 7	Fuse Type and Rating
Power Supply		Fuse Type and Rating

100-120 V AC / 220-240 V AC		IEC/EN 60127-2 Sheet 5
		Bussmann S505/Littelfuse 215
		2 A 250 V T HBC

Note: Refer to the Reference Guide for all power supply, fuse replacement, safety, EMC information and operating conditions

EN/LZT 790 0008/1 R1A 2011-03-30

11 (40)

Contents

Page Copyright Disclaimer Customer Services Europe, Middle East and Africa Contents Quick Start Guide: Connect-Power-Configure List of Figures List of Tables 1 Introduction 1.1Who Should Use this User Guide 1.2What Equipment is Covered by this User Guide 1.3Hardware and Software Options Page Installing the Equipment 2.1Introduction 2.2Operating Voltage 2.3Power Cable and Earthing 2.4Rear Panel Connectors Type of Connector 2.5Connecting the Receiver to the Power Supply Quick Start Guide: Connect-Power-Configure 3.1Connecting the Receiver 3.2Powering the Receiver 3.2.1Switching On 3.2.2Power Up Operating Modes 3.3Configuring the Inputs 3.3.1Transport Stream (ASI) Input 3.3.2Satellite (DVB-Sor DVB-S2)Input (if fitted) 3.4Selecting a Decode Service (Program) 3.5Configuring the Video Output 3.6Configuring the Audio Outputs 3.7Configuring for Single-serviceDecryption 3.8Configuring for Multi-serviceDecryption Front Panel Control 4.1Introduction 4.2Receiver Front Panel 4.3Using the Front Receiver Controls 4.3.1Status LED 4.3.2LCD 4.3.3Arrow Pushbuttons 4.3.4Edit and Save Pushbuttons 4.4Front Panel Menus 4.4.1Menu Structure TS Feed Selection Presets Preset State Select/Save Preset 5 Web Browser Control 5.1Introduction 5.1.1Setting Up Web Browser Remote Control 5.2Using the Web Browser Interface 5.2.1Navigation Header About Function Tabs 5.2.2Viewing the Web Pages 5.3Web Pages 5.3.1Status 5.3.2Device Info Environment Network Settings Modules Trap Destination Table 5.3.3Alarms 5.3.4Customization Web Page 5.3.5CA 5.3.6Input Satellite Input RF Selection Configuration 5.3.7Service Plus 5.3.8Decode 5.3.9Output 5.3.10Download 5.3.11SNMP 5.3.12Presets 5.3.13Save/Load 5.3.14Help 6 Equipment Packaging 6.1Packaging Statement 6.2Packaging Markings Materials Declarations 7.1Overview 7.2For the European Union 7.3For China Disposal of this Equipment 8.1General 8.2For the European Union 9 Recycling