Ericsson RX8310, RX8330, RX8315 2.4Rear Panel Connectors

Installing the Equipment

Warning!

The Technical Earth is not a Protective earth for electric shock protection.

This unit must be correctly earthed through the molded plug supplied. If the local mains supply does not have an earth conductor do not connect the unit. Contact Customer Services for advice.

Before connecting the unit to the supply, check the supply requirements in Annex B of the Reference Guide.

2.4Rear Panel Connectors

Always use the specified cables supplied for signal integrity and compliance with EMC requirements (see the Reference Guide).

Note: Rear panel connectors may differ, depending on the options selected.

RF IN 1-4	IP OUT 1-2	AUDIO OUT (1)	AC POWER
		1-2

ASI OUT 1-2 CVBS ASI INPUT	ETHERNET 1-2 ALARM	TECHNICAL
		EARTH

Figure 1 Rear Panel Connectors (RX8310/BAS with RX83XX/HWO/IP/OUT)

RF IN 1-4	IP OUT 1-2	AUDIO OUT (1)	AC POWER
		1-2

ASI OUT 1-2 CVBS ASI INPUT	ETHERNET 1-2 ALARM	CA	TECHNICAL
		INTERFACE	EARTH

Figure 2 Rear Panel Connectors (RX8315/BAS with RX83XX/HWO/IP/OUT)

EN/LZT 790 0008/1 R1A 2011-03-30

9 (40)

Contents

Page Copyright Disclaimer Customer Services Europe, Middle East and Africa Contents Quick Start Guide: Connect-Power-Configure List of Figures List of Tables 1 Introduction 1.1Who Should Use this User Guide 1.2What Equipment is Covered by this User Guide 1.3Hardware and Software Options Page Installing the Equipment 2.1Introduction 2.2Operating Voltage 2.3Power Cable and Earthing 2.4Rear Panel Connectors Type of Connector 2.5Connecting the Receiver to the Power Supply Quick Start Guide: Connect-Power-Configure 3.1Connecting the Receiver 3.2Powering the Receiver 3.2.1Switching On 3.2.2Power Up Operating Modes 3.3Configuring the Inputs 3.3.1Transport Stream (ASI) Input 3.3.2Satellite (DVB-Sor DVB-S2)Input (if fitted) 3.4Selecting a Decode Service (Program) 3.5Configuring the Video Output 3.6Configuring the Audio Outputs 3.7Configuring for Single-serviceDecryption 3.8Configuring for Multi-serviceDecryption Front Panel Control 4.1Introduction 4.2Receiver Front Panel 4.3Using the Front Receiver Controls 4.3.1Status LED 4.3.2LCD 4.3.3Arrow Pushbuttons 4.3.4Edit and Save Pushbuttons 4.4Front Panel Menus 4.4.1Menu Structure TS Feed Selection Presets Preset State Select/Save Preset 5 Web Browser Control 5.1Introduction 5.1.1Setting Up Web Browser Remote Control 5.2Using the Web Browser Interface 5.2.1Navigation Header About Function Tabs 5.2.2Viewing the Web Pages 5.3Web Pages 5.3.1Status 5.3.2Device Info Environment Network Settings Modules Trap Destination Table 5.3.3Alarms 5.3.4Customization Web Page 5.3.5CA 5.3.6Input Satellite Input RF Selection Configuration 5.3.7Service Plus 5.3.8Decode 5.3.9Output 5.3.10Download 5.3.11SNMP 5.3.12Presets 5.3.13Save/Load 5.3.14Help 6 Equipment Packaging 6.1Packaging Statement 6.2Packaging Markings Materials Declarations 7.1Overview 7.2For the European Union 7.3For China Disposal of this Equipment 8.1General 8.2For the European Union 9 Recycling